Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2019.09–2020.08
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in Bus 1 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

No. 1 CAN junction connector

·

No. 6 CAN junction connector

(w/ Blind Spot Monitor System)



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

w/o Blind Spot Monitor System


C366134E05
1.396,0.635 2.01,0.833 0.615,0.198 10 false CAXH 1.917,0.635 2.115,0.802 0.198,0.167 10 false 9 0.75,1.01 1.365,1.208 0.615,0.198 10 false 120 Ω 1.427,1.177 2.042,1.344 0.615,0.167 10 false CAXL 1.917,1.167 2.25,1.333 0.333,0.167 10 false 24 1.417,2.583 2.031,2.781 0.615,0.198 10 false CA1H 1.438,3.125 2.052,3.323 0.615,0.198 10 false CA1L 1.917,2.583 2.25,2.75 0.333,0.167 10 false 23 1.917,3.135 2.25,3.302 0.333,0.167 10 false 8 5.083,0.615 5.313,0.792 0.229,0.177 10 false 10 5.083,1.146 5.333,1.313 0.25,0.167 10 false 20 5.156,2.573 5.406,2.74 0.25,0.167 10 false 9 5.083,3.135 5.333,3.302 0.25,0.167 10 false 19 5.021,3.583 5.438,3.75 0.417,0.167 10 false F111 5.01,3.75 7.01,3.917 2,0.167 10 false No. 1 CAN Junction Connector 0.469,3.583 0.885,3.75 0.417,0.167 10 false F74 0.469,3.74 3.719,3.99 3.25,0.25 10 false Central Gateway ECU (Network Gateway ECU) 0.781,2.958 1.396,3.156 0.615,0.198 10 false 120 Ω 0.073,0.052 1.542,0.292 1.469,0.24 12 false for LHD:

C366134E06
1.396,0.635 2.01,0.833 0.615,0.198 10 false CAXH 1.917,0.635 2.115,0.802 0.198,0.167 10 false 9 0.75,1.01 1.365,1.208 0.615,0.198 10 false 120 Ω 1.427,1.177 2.042,1.344 0.615,0.167 10 false CAXL 1.917,1.167 2.25,1.333 0.333,0.167 10 false 24 1.417,2.583 2.031,2.781 0.615,0.198 10 false CA1H 1.438,3.125 2.052,3.323 0.615,0.198 10 false CA1L 1.917,2.583 2.25,2.75 0.333,0.167 10 false 23 1.917,3.135 2.25,3.302 0.333,0.167 10 false 8 5.146,0.615 5.313,0.781 0.167,0.167 10 false 6 5.083,1.156 5.333,1.323 0.25,0.167 10 false 12 5.146,2.573 5.396,2.74 0.25,0.167 10 false 5 5.083,3.135 5.333,3.302 0.25,0.167 10 false 11 5.021,3.583 5.438,3.75 0.417,0.167 10 false F164 5.01,3.75 7.01,3.917 2,0.167 10 false No. 1 CAN Junction Connector 0.469,3.583 0.885,3.75 0.417,0.167 10 false F74 0.469,3.74 3.719,3.99 3.25,0.25 10 false Central Gateway ECU (Network Gateway ECU) 0.781,2.958 1.396,3.156 0.615,0.198 10 false 120 Ω 0.052,0.042 1.521,0.281 1.469,0.24 12 false for RHD:


w/ Blind Spot Monitor System


C366137E07
0.708,0.99 1.479,1.188 0.771,0.198 10 false 120 Ω 1.365,0.646 2.135,0.844 0.771,0.198 10 false CAXH 1.385,1.167 2.156,1.365 0.771,0.198 10 false CAXL 1.865,0.635 2.052,0.833 0.188,0.198 10 false 9 1.854,1.167 2.125,1.417 0.271,0.25 10 false 24 1.854,2.688 2.125,2.938 0.271,0.25 10 false 23 1.854,3.25 2.125,3.5 0.271,0.25 10 false 8 0.677,3.083 1.448,3.281 0.771,0.198 10 false 120 Ω 1.365,2.698 2.135,2.896 0.771,0.198 10 false CA1H 1.385,3.25 2.156,3.448 0.771,0.198 10 false CA1L 4.094,0.625 4.344,0.792 0.25,0.167 10 false 10 4.094,1.177 4.344,1.344 0.25,0.167 10 false 20 5.458,0.615 5.708,0.781 0.25,0.167 10 false 9 5.448,1.156 5.698,1.323 0.25,0.167 10 false 19 4.083,1.635 4.583,1.802 0.5,0.167 10 false F111 4.073,1.802 6.24,1.969 2.167,0.167 10 false No. 1 CAN Junction Connector 4.083,2.708 4.719,2.938 0.635,0.229 10 false 10 4.094,3.229 4.594,3.448 0.5,0.219 10 false 21 5.427,2.688 5.677,2.854 0.25,0.167 10 false 11 5.458,3.24 5.708,3.406 0.25,0.167 10 false 22 4.01,3.698 4.51,3.865 0.5,0.167 10 false M104 4.021,3.865 6.104,4.031 2.083,0.167 10 false No. 6 CAN Junction Connector 0.25,3.667 0.75,3.833 0.5,0.167 10 false F74 0.24,3.823 3.323,4.073 3.083,0.25 10 false Central Gateway ECU (Network Gateway ECU) 0.073,0.052 1.542,0.292 1.469,0.24 12 false for LHD:

C366137E08
0.708,0.99 1.479,1.188 0.771,0.198 10 false 120 Ω 1.365,0.646 2.135,0.844 0.771,0.198 10 false CAXH 1.385,1.167 2.156,1.365 0.771,0.198 10 false CAXL 1.865,0.635 2.052,0.833 0.188,0.198 10 false 9 1.854,1.167 2.125,1.417 0.271,0.25 10 false 24 1.854,2.688 2.125,2.938 0.271,0.25 10 false 23 1.854,3.25 2.125,3.5 0.271,0.25 10 false 8 0.677,3.083 1.448,3.281 0.771,0.198 10 false 120 Ω 1.365,2.698 2.135,2.896 0.771,0.198 10 false CA1H 1.385,3.25 2.156,3.448 0.771,0.198 10 false CA1L 4.177,0.625 4.427,0.792 0.25,0.167 10 false 6 4.094,1.177 4.344,1.344 0.25,0.167 10 false 12 5.458,0.615 5.708,0.781 0.25,0.167 10 false 5 5.448,1.156 5.698,1.323 0.25,0.167 10 false 11 4.083,1.635 4.583,1.802 0.5,0.167 10 false F164 4.073,1.802 6.24,1.969 2.167,0.167 10 false No. 1 CAN Junction Connector 3.688,2.708 4.719,2.938 1.031,0.229 10 false 8*1, 10*2 3.615,3.229 4.594,3.448 0.979,0.219 10 false 19*1, 21*2 5.427,2.688 5.677,2.854 0.25,0.167 10 false 11 5.458,3.24 5.708,3.406 0.25,0.167 10 false 22 4.01,3.698 4.51,3.865 0.5,0.167 10 false M104 4.021,3.865 6.104,4.031 2.083,0.167 10 false No. 6 CAN Junction Connector 0.25,3.667 0.75,3.833 0.5,0.167 10 false F74 0.24,3.823 3.323,4.073 3.083,0.25 10 false Central Gateway ECU (Network Gateway ECU) 0.469,4.417 2.917,4.615 2.448,0.198 10 false *1: for TMC Made 2,4.417 4.604,4.615 2.604,0.198 10 false *2: for TMMT Made 0.073,0.042 1.542,0.281 1.469,0.24 12 false for RHD:


CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the LDA main switch on and then drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 52 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK VEHICLE TYPE

B

9.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/o Blind Spot Monitor System A
w/ Blind Spot Monitor System B



A

3.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)

B

5.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C328881C39
3.313,0.385 3.813,0.635 0.5,0.25 4.74,1.417 5.552,0.594 true 4.708,1.646 5.542,2.333 true 5.083,1.625 5.677,2 true 5.083,1.406 5.635,1.146 true 0.167,0.094 0.479,0.25 0.313,0.156 10 false *a 5.625,0.5 6.208,0.813 0.583,0.313 10 false CANH*b 5.604,2.26 6.188,2.51 0.583,0.25 10 false CANL*b 3.406,0.417 4.094,0.708 0.688,0.292 10 false F111 5.75,1.906 6.333,2.156 0.583,0.25 10 false CANL*b 5.708,1.052 6.292,1.365 0.583,0.313 10 false CANH*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F111-9 (CANH) - F111-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F111-10 (CANH) - F111-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



Result:
Result
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

4.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 1 CAN JUNCTION CONNECTOR)
4.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F111 No. 1 CAN junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C367277C01
1.438,0.167 1.938,0.417 0.5,0.25 2.25,1.833 2.677,1.208 true 2.833,1.833 2.906,1.219 true 2.552,0.927 2.417,0.333 true 2.74,0.906 2.917,0.333 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.552,0.208 1.948,0.375 0.396,0.167 10 false F74 2.052,0.208 2.552,0.375 0.5,0.167 10 false CA1L 2.979,0.198 3.385,0.365 0.406,0.167 10 false CAXH 2.656,1.865 3.156,2.031 0.5,0.167 10 false CAXL 1.969,1.865 2.469,2.031 0.5,0.167 10 false CA1H
*a Front view of wire harness connector
to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-23 (CA1H) - F74-9 (CAXH) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F74-8 (CA1L) - F74-24 (CAXL) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 1 CAN JUNCTION CONNECTOR)

5.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 6 CAN junction connector.


c.
C425651C04
1.417,0.75 1.917,1 0.5,0.25 2.292,1.771 2.583,0.885 true 2.521,1.75 2.75,1.167 true 2.531,2.74 2.313,2.01 true 2.75,2.5 2.521,2.021 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.49,0.792 1.948,1 0.458,0.208 10 false M104 2.813,1.083 3.365,1.333 0.552,0.25 10 false CANH*c 2.646,0.76 3.292,0.927 0.646,0.167 10 false CANH*b 2.563,2.792 3.208,2.958 0.646,0.167 10 false CANL*b 2.75,2.521 3.302,2.688 0.552,0.167 10 false CANL*c
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to No. 1 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
M104-10 (CANH) - M104-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
M104-11 (CANH) - M104-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 1 CAN junction connector



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 1 CAN junction connector) C



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

6.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 CAN JUNCTION CONNECTOR)

C

7.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the M104 No. 6 CAN junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C367277C01
1.438,0.167 1.938,0.417 0.5,0.25 2.25,1.833 2.677,1.208 true 2.833,1.833 2.906,1.219 true 2.552,0.927 2.417,0.333 true 2.74,0.906 2.917,0.333 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.552,0.208 1.948,0.375 0.396,0.167 10 false F74 2.052,0.208 2.552,0.375 0.5,0.167 10 false CA1L 2.979,0.198 3.385,0.365 0.406,0.167 10 false CAXH 2.656,1.865 3.156,2.031 0.5,0.167 10 false CAXL 1.969,1.865 2.469,2.031 0.5,0.167 10 false CA1H
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-23 (CA1H) - F74-9 (CAXH) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F74-8 (CA1L) - F74-24 (CAXL) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 CAN JUNCTION CONNECTOR)

7.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the M104 No. 6 CAN junction connector.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C328881C40
3.313,0.385 3.813,0.635 0.5,0.25 4.74,1.417 5.552,0.594 true 4.708,1.646 5.542,2.333 true 5.083,1.625 5.677,2 true 5.083,1.406 5.635,1.146 true 0.167,0.094 0.479,0.25 0.313,0.156 10 false *a 5.625,0.5 6.208,0.813 0.583,0.313 10 false CANH*b 5.604,2.26 6.188,2.51 0.583,0.25 10 false CANL*b 3.406,0.417 4.094,0.708 0.688,0.292 10 false F111 5.75,1.906 6.333,2.156 0.583,0.25 10 false CANL*c 5.708,1.052 6.292,1.365 0.583,0.313 10 false CANH*c
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 6 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F111-9 (CANH) - F111-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 6 CAN junction connector
F111-10 (CANH) - F111-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



Result:
Result Proceed to
OK A
NG (Line to No. 6 CAN junction connector) B
NG (Line to central gateway ECU (network gateway ECU)) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

C

8.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 1 CAN JUNCTION CONNECTOR)
8.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F111 No. 1 CAN junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C367277C01
1.438,0.167 1.938,0.417 0.5,0.25 2.25,1.833 2.677,1.208 true 2.833,1.833 2.906,1.219 true 2.552,0.927 2.417,0.333 true 2.74,0.906 2.917,0.333 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.552,0.208 1.948,0.375 0.396,0.167 10 false F74 2.052,0.208 2.552,0.375 0.5,0.167 10 false CA1L 2.979,0.198 3.385,0.365 0.406,0.167 10 false CAXH 2.656,1.865 3.156,2.031 0.5,0.167 10 false CAXL 1.969,1.865 2.469,2.031 0.5,0.167 10 false CA1H
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-23 (CA1H) - F74-9 (CAXH) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F74-8 (CA1L) - F74-24 (CAXL) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 1 CAN JUNCTION CONNECTOR)

9.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/o Blind Spot Monitor System A
w/ Blind Spot Monitor System B



A

10.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)

B

12.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)
10.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C404458C47
3.271,0.583 3.771,0.833 0.5,0.25 4.042,1.427 4.625,0.792 true 4.354,1.448 4.885,1.052 true 4.375,1.635 4.896,1.823 true 4.021,1.625 4.646,2.188 true 0.104,0.135 0.406,0.365 0.302,0.229 10 false *a 4.938,0.958 5.542,1.167 0.604,0.208 10 false CANH*b 3.354,0.625 3.76,0.792 0.406,0.167 10 false F164 4.938,1.74 5.542,1.948 0.604,0.208 10 false CANL*b 4.708,2.104 5.313,2.313 0.604,0.208 10 false CANL*b 4.667,0.667 5.271,0.875 0.604,0.208 10 false CANH*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F164-5 (CANH) - F164-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F164-6 (CANH) - F164-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



Result:
Result
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

11.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 1 CAN JUNCTION CONNECTOR)
11.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F164 No. 1 CAN junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C367277C01
1.438,0.167 1.938,0.417 0.5,0.25 2.25,1.833 2.677,1.208 true 2.833,1.833 2.906,1.219 true 2.552,0.927 2.417,0.333 true 2.74,0.906 2.917,0.333 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.552,0.208 1.948,0.375 0.396,0.167 10 false F74 2.052,0.208 2.552,0.375 0.5,0.167 10 false CA1L 2.979,0.198 3.385,0.365 0.406,0.167 10 false CAXH 2.656,1.865 3.156,2.031 0.5,0.167 10 false CAXL 1.969,1.865 2.469,2.031 0.5,0.167 10 false CA1H
*a Front view of wire harness connector
to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-23 (CA1H) - F74-9 (CAXH) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F74-8 (CA1L) - F74-24 (CAXL) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 1 CAN JUNCTION CONNECTOR)

12.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 6 CAN junction connector.


c.
C425651C17
1.417,0.75 1.917,1 0.5,0.25 2.292,1.771 2.667,0.875 true 2.521,1.75 2.75,1.167 true 2.531,2.74 2.313,2.01 true 2.927,2.479 2.521,2.021 true 1.844,2.719 2.021,2.042 true 2.031,1.74 2.5,0.521 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.49,0.792 1.948,1 0.458,0.208 10 false M104 2.813,1.083 3.365,1.333 0.552,0.25 10 false CANH*d 2.74,0.792 3.385,0.958 0.646,0.167 10 false CANH*c 2.333,2.792 2.979,2.958 0.646,0.167 10 false CANL*c 2.75,2.521 3.302,2.688 0.552,0.167 10 false CANL*d 1.583,2.76 2.229,2.927 0.646,0.167 10 false CANL*b 2.531,0.438 3.177,0.604 0.646,0.167 10 false CANH*b
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU) (for TMC Made)
*c to Central Gateway ECU (Network Gateway ECU) (for TMMT Made)
*d to No. 1 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMC Made
Tester Connection Condition Specified Condition Connected to
M104-8 (CANH) - M104-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
M104-11 (CANH) - M104-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 1 CAN junction connector

for TMMT Made
Tester Connection Condition Specified Condition Connected to
M104-10 (CANH) - M104-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
M104-11 (CANH) - M104-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 1 CAN junction connector



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 1 CAN junction connector) C



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

13.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 CAN JUNCTION CONNECTOR)

C

14.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
13.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the M104 No. 6 CAN junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C367277C01
1.438,0.167 1.938,0.417 0.5,0.25 2.25,1.833 2.677,1.208 true 2.833,1.833 2.906,1.219 true 2.552,0.927 2.417,0.333 true 2.74,0.906 2.917,0.333 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.552,0.208 1.948,0.375 0.396,0.167 10 false F74 2.052,0.208 2.552,0.375 0.5,0.167 10 false CA1L 2.979,0.198 3.385,0.365 0.406,0.167 10 false CAXH 2.656,1.865 3.156,2.031 0.5,0.167 10 false CAXL 1.969,1.865 2.469,2.031 0.5,0.167 10 false CA1H
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-23 (CA1H) - F74-9 (CAXH) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F74-8 (CA1L) - F74-24 (CAXL) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 CAN JUNCTION CONNECTOR)

14.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the M104 No. 6 CAN junction connector.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C404458C48
3.271,0.583 3.771,0.833 0.5,0.25 4.042,1.427 4.625,0.792 true 4.354,1.448 4.885,1.052 true 4.375,1.635 4.896,1.823 true 4.021,1.625 4.646,2.188 true 0.104,0.135 0.406,0.365 0.302,0.229 10 false *a 4.938,0.958 5.542,1.167 0.604,0.208 10 false CANH*c 3.354,0.625 3.76,0.792 0.406,0.167 10 false F164 4.938,1.74 5.542,1.948 0.604,0.208 10 false CANL*c 4.708,2.104 5.313,2.313 0.604,0.208 10 false CANL*b 4.667,0.667 5.271,0.875 0.604,0.208 10 false CANH*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 6 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F164-5 (CANH) - F164-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 6 CAN junction connector
F164-6 (CANH) - F164-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



Result:
Result Proceed to
OK A
NG (Line to No. 6 CAN junction connector) B
NG (Line to central gateway ECU (network gateway ECU)) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

C

15.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 1 CAN JUNCTION CONNECTOR)
15.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F164 No. 1 CAN junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C367277C01
1.438,0.167 1.938,0.417 0.5,0.25 2.25,1.833 2.677,1.208 true 2.833,1.833 2.906,1.219 true 2.552,0.927 2.417,0.333 true 2.74,0.906 2.917,0.333 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.552,0.208 1.948,0.375 0.396,0.167 10 false F74 2.052,0.208 2.552,0.375 0.5,0.167 10 false CA1L 2.979,0.198 3.385,0.365 0.406,0.167 10 false CAXH 2.656,1.865 3.156,2.031 0.5,0.167 10 false CAXL 1.969,1.865 2.469,2.031 0.5,0.167 10 false CA1H
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-23 (CA1H) - F74-9 (CAXH) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F74-8 (CA1L) - F74-24 (CAXL) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 1 CAN JUNCTION CONNECTOR)