Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2019.09–2020.08
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in Bus 4 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

Airbag sensor assembly

·

No. 5 CAN junction connector

(for LHD)

·

No. 4 CAN junction connector

(for LHD)

·

No. 4 CAN junction connector

(for RHD)

·

No. 5 CAN junction connector

(for RHD)



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

for LHD


C366146E03
0.49,1 1.26,1.198 0.771,0.198 10 false 120 Ω 6.281,1 7.052,1.198 0.771,0.198 10 false 120 Ω 1.135,0.615 1.75,0.813 0.615,0.198 10 false CA2H 1.156,1.146 1.771,1.344 0.615,0.198 10 false CA2L 1.656,0.615 1.948,0.833 0.292,0.219 10 false 22 1.656,1.146 1.948,1.365 0.292,0.219 10 false 7 1.958,1.146 2.25,1.365 0.292,0.219 10 false 13 2.031,0.615 2.323,0.833 0.292,0.219 10 false 2 3.313,1.146 3.604,1.365 0.292,0.219 10 false 12 3.313,0.615 3.604,0.833 0.292,0.219 10 false 1 3.667,1.146 3.958,1.365 0.292,0.219 10 false 17 3.74,0.615 4.031,0.833 0.292,0.219 10 false 7 5.052,1.146 5.344,1.365 0.292,0.219 10 false 11 5.052,0.615 5.344,0.833 0.292,0.219 10 false 1 5.344,1.146 5.635,1.365 0.292,0.219 10 false 27 5.344,0.615 5.635,0.833 0.292,0.219 10 false 26 5.646,0.615 6.26,0.813 0.615,0.198 10 false CANH 5.646,1.146 6.26,1.344 0.615,0.198 10 false CANL 0.042,1.625 0.656,1.823 0.615,0.198 10 false F74 0.042,1.792 2.01,2.208 1.969,0.417 10 false Central Gateway ECU (Network Gateway ECU) 2.115,1.792 3.427,2.417 1.313,0.625 10 false No. 5 CAN Junction Connector 2.115,1.625 3.375,2.281 1.26,0.656 10 false F124 3.823,1.802 5.083,2.458 1.26,0.656 10 false No. 4 CAN Junction Connector 3.823,1.635 4.313,1.844 0.49,0.208 10 false F116 5.438,1.792 7.083,2.063 1.646,0.271 10 false Airbag Sensor Assembly 5.427,1.625 5.979,1.844 0.552,0.219 10 false F150


for RHD


C366149E04
0.479,1 1.25,1.198 0.771,0.198 10 false 120 Ω 6.292,0.979 7.063,1.177 0.771,0.198 10 false 120 Ω 1.146,0.615 1.76,0.813 0.615,0.198 10 false CA2H 1.146,1.146 1.76,1.344 0.615,0.198 10 false CA2L 1.656,0.615 1.958,0.813 0.302,0.198 10 false 22 1.656,1.146 1.958,1.344 0.302,0.198 10 false 7 2.021,0.615 2.323,0.813 0.302,0.198 10 false 2 1.948,1.146 2.25,1.344 0.302,0.198 10 false 12 3.323,1.146 3.625,1.344 0.302,0.198 10 false 11 3.323,0.615 3.625,0.813 0.302,0.198 10 false 1 3.667,1.146 3.969,1.344 0.302,0.198 10 false 17 3.74,0.604 4.042,0.802 0.302,0.198 10 false 6 5.052,1.146 5.354,1.344 0.302,0.198 10 false 12 5.052,0.615 5.354,0.813 0.302,0.198 10 false 1 5.333,1.146 5.635,1.344 0.302,0.198 10 false 27 5.333,0.615 5.635,0.813 0.302,0.198 10 false 26 5.646,0.615 6.354,0.813 0.708,0.198 10 false CANH 5.646,1.146 6.354,1.344 0.708,0.198 10 false CANL 0.042,1.635 0.656,1.833 0.615,0.198 10 false F74 0.042,1.792 2.031,2.229 1.99,0.438 10 false Central Gateway ECU (Network Gateway ECU) 2.115,1.802 3.365,2.354 1.25,0.552 10 false No. 5 CAN Junction Connector 2.115,1.635 2.594,1.865 0.479,0.229 10 false F118 3.833,1.802 5.083,2.354 1.25,0.552 10 false No. 4 CAN Junction Connector 3.833,1.635 4.354,1.823 0.521,0.188 10 false F115 5.406,1.635 5.927,1.823 0.521,0.188 10 false F150 5.417,1.802 7,2.083 1.583,0.281 10 false Airbag Sensor Assembly


CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the LDA main switch on and then drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 52 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)

B

6.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)
2.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 5 CAN junction connector.


c.
C366166C11
1.417,0.75 1.917,1 0.5,0.25 0.906,1.74 0.667,1.25 true 1.146,1.75 1.375,1.167 true 0.667,2.583 0.917,2.031 true 1.333,2.583 1.094,2.021 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.531,0.792 1.927,0.958 0.396,0.167 10 false F124 1.448,1.063 2,1.313 0.552,0.25 10 false CANH*c 0.083,1.146 0.729,1.313 0.646,0.167 10 false CANH*b 0.104,2.49 0.75,2.656 0.646,0.167 10 false CANL*b 1.427,2.479 1.979,2.646 0.552,0.167 10 false CANL*c
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F124-1 (CANH) - F124-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 4 CAN junction connector
F124-2 (CANH) - F124-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 4 CAN junction connector) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

3.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 5 CAN JUNCTION CONNECTOR)

C

4.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the F124 No. 5 CAN junction connector.


b.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


c.
C367304C01
1.458,0.167 1.958,0.417 0.5,0.25 1.823,1.885 2.323,1.219 true 2.448,0.917 2.865,0.333 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.604,0.198 1.938,0.365 0.333,0.167 10 false F74 2.938,0.229 3.417,0.5 0.479,0.271 10 false CA2L 1.396,1.781 2.01,1.979 0.615,0.198 10 false CA2H
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-22 (CA2H) - F74-7 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 5 CAN JUNCTION CONNECTOR)

4.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the F124 No. 5 CAN junction connector.


b.

Disconnect the No. 4 CAN junction connector.


c.
C328876C18
1.469,0.25 1.969,0.5 0.5,0.25 2.167,1.094 2.5,0.406 true 2.177,1.302 2.51,1.833 true 0.448,1.094 0.667,0.5 true 0.5,1.302 0.75,1.75 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.573,0.292 2.146,0.531 0.573,0.24 10 false F116 2.573,0.292 3.146,0.5 0.573,0.208 10 false CANH*c 2.583,1.74 3.146,1.896 0.563,0.156 10 false CANL*c 0.708,0.365 1.281,0.573 0.573,0.208 10 false CANH*b 0.792,1.729 1.365,1.938 0.573,0.208 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly
*c to No. 5 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F116-1 (CANH) - F116-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Airbag sensor assembly
F116-7 (CANH) - F116-17 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 5 CAN junction connector



Result:
Result Proceed to
OK A
NG (Line to No. 5 CAN junction connector) B
NG (Line to Airbag sensor assembly) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

C

5.CHECK FOR OPEN IN CAN MAIN BUS LINES (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN CAN MAIN BUS LINES (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the F116 No. 4 CAN junction connector.


b.

Disconnect the airbag sensor assembly connector.


c.
C392555C21
0.354,0.979 0.771,1.229 0.417,0.25 2.844,1.875 2.156,1.323 true 0.792,1.865 2.042,1.333 true 0.188,0.156 0.573,0.448 0.385,0.292 10 false *a 0.406,1.01 0.813,1.25 0.406,0.24 10 false F150 0.354,1.802 0.969,2 0.615,0.198 10 false CANH 2.917,1.802 3.375,2.031 0.458,0.229 10 false CANL
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F150-26 (CANH) - F150-27 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

6.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 5 CAN junction connector.


c.
C328876C13
1.469,0.25 1.969,0.5 0.5,0.25 0.771,1.083 2.167,0.5 true 0.76,1.302 2.083,1.75 true 0.448,1.094 0.667,0.5 true 0.5,1.302 0.75,1.75 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.583,0.292 2.052,0.479 0.469,0.188 10 false F118 2.25,0.385 2.823,0.594 0.573,0.208 10 false CANH*c 2.156,1.646 2.719,1.802 0.563,0.156 10 false CANL*c 0.708,0.365 1.281,0.573 0.573,0.208 10 false CANH*b 0.792,1.729 1.365,1.938 0.573,0.208 10 false CANL*b
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F118-1 (CANH) - F118-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 4 CAN junction connector
F118-2 (CANH) - F118-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 4 CAN junction connector) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

7.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 5 CAN JUNCTION CONNECTOR)

C

8.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the F118 No. 5 CAN junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C367304C01
1.458,0.167 1.958,0.417 0.5,0.25 1.823,1.885 2.323,1.219 true 2.448,0.917 2.865,0.333 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.604,0.198 1.938,0.365 0.333,0.167 10 false F74 2.938,0.229 3.417,0.5 0.479,0.271 10 false CA2L 1.396,1.781 2.01,1.979 0.615,0.198 10 false CA2H
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-22 (CA2H) - F74-7 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 5 CAN JUNCTION CONNECTOR)

8.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the F118 No. 5 CAN junction connector.


b.

Disconnect the No. 4 CAN junction connector.


c.
C366166C12
1.417,0.75 1.917,1 0.5,0.25 0.917,1.771 0.76,1.188 true 1.75,1.75 2,1.167 true 0.75,2.5 0.917,2.031 true 1.979,2.5 1.75,2.021 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.51,0.792 1.906,0.958 0.396,0.167 10 false F115 2.073,1.073 2.625,1.323 0.552,0.25 10 false CANH*c 0.177,1.094 0.823,1.26 0.646,0.167 10 false CANH*b 0.49,2.531 1.135,2.698 0.646,0.167 10 false CANL*b 1.802,2.542 2.354,2.708 0.552,0.167 10 false CANL*c
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly
*c to No. 5 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F115-1 (CANH) - F115-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Airbag sensor assembly
F115-6 (CANH) - F115-17 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 5 CAN junction connector



Result:
Result Proceed to
OK A
NG (Line to No. 5 CAN junction connector) B
NG (Line to Airbag sensor assembly) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 4 CAN JUNCTION CONNECTOR)

C

9.CHECK FOR OPEN IN CAN MAIN BUS LINES (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
9.CHECK FOR OPEN IN CAN MAIN BUS LINES (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the F115 No. 4 CAN junction connector.


b.

Disconnect the airbag sensor assembly connector.


c.
C392555C21
0.354,0.979 0.771,1.229 0.417,0.25 2.844,1.875 2.156,1.323 true 0.792,1.865 2.042,1.333 true 0.188,0.156 0.573,0.448 0.385,0.292 10 false *a 0.406,1.01 0.813,1.25 0.406,0.24 10 false F150 0.354,1.802 0.969,2 0.615,0.198 10 false CANH 2.917,1.802 3.375,2.031 0.458,0.229 10 false CANL
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F150-26 (CANH) - F150-27 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)