Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › from 2019.09
RM32K0E _59 Vehicle Exterior _061162 LIGHTING (EXT) _0303092 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM C

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  B2424  Headlight Beam Level Control Motor LH Lost Communication  B2425  Headlight Beam Level Control Motor RH Lost Communication  


DESCRIPTION

Each headlight ECU sub-assembly and headlight swivel and leveling motor communicate via LIN communication.

The headlight swivel and leveling motor operates according to power supplied and automatic headlight beam level control signals from its respective headlight ECU sub-assembly and sends its operating state to the headlight ECU sub-assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2424 Headlight Beam Level Control Motor LH Lost Communication Malfunction in LIN communication error
·

Headlight unit assembly LH

·

Headlight unit assembly RH

·

Harness or connector

·

Headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly RH


AFS
B2425 Headlight Beam Level Control Motor RH Lost Communication Malfunction in LIN communication error
·

Headlight unit assembly RH

·

Headlight unit assembly LH

·

Harness or connector

·

Headlight ECU sub-assembly RH

·

Headlight ECU sub-assembly LH


AFS

WIRING DIAGRAM

E399064E26
0.698,3.063 2.792,3.281 2.094,0.219 10 false Headlight ECU Sub-assembly LH 0.75,6.76 2.844,6.979 2.094,0.219 10 false Headlight ECU Sub-assembly RH 0.635,0.802 1.094,1 0.458,0.198 10 false A95 0.635,4.51 1.094,4.708 0.458,0.198 10 false A17 1,0.656 1.458,0.854 0.458,0.198 10 false LINL 0.969,4.365 1.427,4.563 0.458,0.198 10 false LINL 2.031,0.646 2.49,0.844 0.458,0.198 10 false LINLI 2.01,4.333 2.469,4.531 0.458,0.198 10 false LINLI 1.958,1.208 2.417,1.406 0.458,0.198 10 false ACTBI 1.948,1.781 2.406,1.979 0.458,0.198 10 false ACTGI 1.927,4.927 2.385,5.125 0.458,0.198 10 false ACTBI 1.927,5.458 2.385,5.656 0.458,0.198 10 false ACTGI 3.583,2.667 5.75,2.938 2.167,0.271 10 false Headlight Unit Assembly LH 3.469,6.396 5.49,6.635 2.021,0.24 10 false Headlight Unit Assembly RH 0.802,7.385 2.896,7.604 2.094,0.219 10 false : LIN Communication Line 4.719,2.177 6.927,2.542 2.208,0.365 10 false Headlight Swivel and Leveling Motor 0.677,0.615 1.01,0.802 0.333,0.188 10 false 20 0.677,4.323 1.01,4.51 0.333,0.188 10 false 20 2.521,0.802 2.813,1 0.292,0.198 10 false C 2.542,1.333 2.833,1.531 0.292,0.198 10 false B 2.552,1.875 2.844,2.073 0.292,0.198 10 false B 2.531,4.5 2.823,4.698 0.292,0.198 10 false C 2.542,5.052 2.833,5.25 0.292,0.198 10 false B 2.552,5.573 2.844,5.771 0.292,0.198 10 false B 2.542,0.604 2.875,0.792 0.333,0.188 10 false 13 2.542,1.146 2.875,1.333 0.333,0.188 10 false 9 2.521,1.667 2.854,1.854 0.333,0.188 10 false 17 2.5,4.281 2.833,4.469 0.333,0.188 10 false 13 2.552,4.823 2.885,5.01 0.333,0.188 10 false 9 2.51,5.385 2.844,5.573 0.333,0.188 10 false 17 1.365,1.104 1.823,1.302 0.458,0.198 10 false IG 1.448,0.354 2.021,0.594 0.573,0.24 10 false LIN I/F 1.385,4.844 1.844,5.042 0.458,0.198 10 false IG 4.698,5.875 6.906,6.24 2.208,0.365 10 false Headlight Swivel and Leveling Motor

CAUTION / NOTICE / HINT

NOTICE:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>INITIALIZATION


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / AFS / Clear DTCs.


e.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch to on (IG).


c.

Wait 10 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / AFS / Trouble Codes.


f.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165
OK:

DTC B2424 and B2425 are not output.



Result:
Result Proceed to
OK A
NG (DTC B2424 is output) B
NG (DTC B2425 is output) C
NG (DTC B2424 and B2425 are output) D



A

B

3.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH

C

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

D

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)
3.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH
E374538C83
2.104,0.302 2.573,0.552 0.469,0.25 5.771,0.563 6.24,0.813 0.469,0.25 2.125,1.26 2.271,2.01 true 5.76,1.469 5.521,2.073 true 0.188,0.115 0.5,0.313 0.313,0.198 10 false *a 2.198,0.354 2.51,0.552 0.313,0.198 10 false A95 2.188,2.073 2.552,2.302 0.365,0.229 10 false LINL 5.302,2.115 5.667,2.344 0.365,0.229 10 false LINLI 5.948,0.604 6.313,0.833 0.365,0.229 10 false C
*a Component without harness connected
(Headlight ECU Sub-assembly LH)
- -


a.

Remove the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A95-20 (LINL) - C-13 (LINLI) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Disconnect the A95 headlight ECU sub-assembly LH connector.


b.

Disconnect the A17 headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A95-20 (LINL) - A17-20 (LINL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH (LINL TERMINAL SIGNAL OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH (LINL TERMINAL SIGNAL OUTPUT)
E416744C08
1.5,0.531 1.896,0.833 0.396,0.302 1.938,2.49 2.188,1.969 true 0.24,0.24 0.552,0.438 0.313,0.198 10 false *a 1.573,0.604 1.885,0.802 0.313,0.198 10 false A17 1.688,2.49 2.229,2.771 0.542,0.281 10 false LINL
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly RH)


a.

Disconnect the headlight ECU sub-assembly RH connector.


b.

Using the GTS, check the waveform.

OK:
Tester Connection Switch Condition Specified Condition
A17-20 (LINL) - Body ground Power switch on (IG) Pulse generation



Result:
Proceed to
OK
NG



OK

6.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

6.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH
E374538C61
2.104,0.302 2.573,0.552 0.469,0.25 5.771,0.563 6.24,0.813 0.469,0.25 2.104,1.25 2.271,2.01 true 5.75,1.469 5.573,2.073 true 0.188,0.115 0.5,0.313 0.313,0.198 10 false *a 2.219,0.354 2.531,0.552 0.313,0.198 10 false A17 2.229,2.073 2.594,2.302 0.365,0.229 10 false LINL 5.292,2.125 5.656,2.354 0.365,0.229 10 false LINLI 5.948,0.604 6.313,0.833 0.365,0.229 10 false C
*a Component without harness connected
(Headlight ECU Sub-assembly RH)
- -


a.

Remove the headlight ECU sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-20 (LINL) - C-13 (LINLI) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Disconnect the A95 headlight ECU sub-assembly LH connector.


b.

Disconnect the A17 headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A95-20 (LINL) or A17-20 (LINL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / AFS / Clear DTCs.


e.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Disconnect the A17 headlight ECU sub-assembly RH connector.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch to on (IG).


d.

Wait 10 seconds or more.


e.

Turn the GTS on.


f.

Enter the following menus: Body Electrical / AFS / Trouble Codes.


g.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165

Result:
Result Proceed to
DTC B2425 is output A
DTC B2424 and B2425 are output B



A

10.CLEAR DTC

B

12.CLEAR DTC
10.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / AFS / Clear DTCs.


e.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165

Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Remove the headlight ECU sub-assembly RH from headlight unit assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Reconnect the A17 headlight ECU sub-assembly RH connector.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch to on (IG).


e.

Wait 10 seconds or more.


f.

Turn the GTS on.


g.

Enter the following menus: Body Electrical / AFS / Trouble Codes.


h.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165

Result:
Result Proceed to
DTC B2425 is output A
DTC B2424 and B2425 are output B



A

B

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

12.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / AFS / Clear DTCs.


e.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165

Result:
Proceed to
NEXT



NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC
a.

Remove the headlight ECU sub-assembly LH from headlight unit assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Reconnect the A95 headlight ECU sub-assembly LH connector.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch to on (IG).


e.

Wait 10 seconds or more.


f.

Turn the GTS on.


g.

Enter the following menus: Body Electrical / AFS / Trouble Codes.


h.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165

Result:
Result Proceed to
DTC B2424 is output A
DTC B2424 and B2425 are output B



A

B

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH