When the engine is being cranked, the start request signal output from the hybrid vehicle control ECU is input to the ECM, and the NE signal generated by the crankshaft position sensor is also input to the ECM. Thus, the ECM interprets that the engine is being cranked, and turns an internal transistor on, causing current to flow to the C/OPN relay. The fuel pump then operates the NE signal is input into the ECM with the engine running, the ECM keeps the transistor on.
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.
| Tester Display |
|---|
| Activate the Circuit Relay |
According to the display on the GTS, perform the Active Test and check that fuel pump operating sounds can be heard.
Operating sounds can be heard from the fuel pump.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
| Tester Display |
|---|
| Inspection Mode |
Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
Read the values displayed on the GTS while the engine is cranking.
Values are displayed continuously.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the C/OPN relay.
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the C/OPN relay from the No. 2 engine room relay block.
Disconnect the A38 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (C/OPN relay holder) - A38-41 (FC) | Always | Below 1 Ω |
| 2 (C/OPN relay holder) or A38-41 (FC) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 integration relay.
Remove the C/OPN relay from the No. 2 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1A-9 - 1 (C/OPN relay holder) | Always | Below 1 Ω |
| 1B-4 - 5 (C/OPN relay holder) | Always | Below 1 Ω |
| 1A-9 or 1 (C/OPN relay holder) - Body ground and other terminals | Always | 10 kΩ or higher |
| 1B-4 or 5 (C/OPN relay holder) - Body ground and other terminals | Always | 10 kΩ or higher |
If a short is detected in any of the above circuits, there may be a malfunction in the circuit of a connected ECU.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the C/OPN relay from the No. 2 engine room relay block.
Disconnect the M14 fuel pump connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (C/OPN relay holder) - M14-4 (B) | Always | Below 1 Ω |
| 3 (C/OPN relay holder) or M14-4 (B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M14 fuel pump connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M14-5 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel pump.
Click hereEngine / Hybrid System>2ZR-FXE (FUEL)>FUEL PUMP>INSPECTION
Perform "Inspection After Repair" after replacing the fuel pump.
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG