A differential pressure sensor is installed to monitor the pressure before the GPF (Gasoline Particulate Filter) catalytic converter. The sensor is a semiconductor type that is not affected by the exhaust gas. The differential pressure sensor outputs the difference between the atmospheric pressure and the pressure before the GPF catalyst.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P245211 | Particulate Filter Pressure Sensor "A" Circuit Short to Ground | The output voltage from the differential pressure sensor is below 0.375 V for 3 seconds or more (1 trip detection logic). | ·
Open or short in differential pressure sensor circuit ·
Differential pressure sensor ·
ECM |
Does not come on | DTC stored | SAE Code: P2454 |
When a DTC is output, check the Data List item "GPF Differential Pressure Sensor Bank 1" using the GTS.
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
| DTC No. | GPF Differential Pressure Sensor Bank 1 | Malfunction |
|---|---|---|
| P245211 | Approximately -5 kPa (-0.73 psi) | ·
Short in PEX circuit to ground ·
Short in PEX circuit to EPEX circuit ·
Open in VCPX circuit |
If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
In order to detect abnormality in the differential pressure sensor, the ECM always monitors the output voltage from the sensor. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the sensor circuit.
Example:
When the sensor output voltage is below 0.375 V for 3 seconds or more, the ECM stores a DTC.
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and wait 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P245211.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
Refer to DTC P244B00.
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P244B00
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
Disconnect the C38 differential pressure sensor connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C38-3 (VC) - C38-1 (E2) | Power switch on (IG) | 4.5 to 5.5 V |
| C38-2 (PEX) - C38-1 (E2) | Power switch on (IG) | 0.5 to 1.0 V |
Turn the power switch off and wait for at least 30 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C38-3 (VC) - C38-2 (PEX) | Power Switch off | 190 to 210 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C38 differential pressure sensor connector.
Disconnect the C63 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C38-3 (VC) - C63-117 (VCPX) | Always | Below 1 Ω |
| C38-2 (PEX) or C63-86 (PEX) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG