Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › from 2020.08
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295698 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P244B00  Particulate Filter Differential Pressure Too High Bank 1  


DESCRIPTION

The GPF (Gasoline Particulate Filter) system is an exhaust purification system for processing the PM (Particulate Matter) discharged from the engine. The GPF catalyst has a porous ceramic structure that collects PM, and the collected PM is oxidized as it bonds with oxygen molecules under high temperature. When the fuel cut operation is performed after the GPF rises to a high temperature under high load operation, PM is oxidized, but under low temperature conditions, PM oxidation is insufficient and deposits accumulate. When the GPF is clogged by PM and "Exhaust Filter Full" is displayed on the multi-information display or GPF warning light comes on, perform particulate filter regeneration using the GTS.

A differential pressure sensor is installed to monitor the pressure before the GPF catalytic converter. The sensor is a semiconductor type that is not affected by the exhaust gas. The differential pressure sensor outputs the difference between the atmospheric pressure and the pressure before the GPF catalyst.

A418810E05
4.427,1.302 4.323,1.313 4.323,1.313 4.073,0.865 false 4.531,2.49 4.854,2.177 4.854,2.177 4.979,2.167 false 5.823,4.698 5.875,4.458 5.875,4.458 6.01,4.458 false 5.302,3.604 5.146,3.604 5.146,3.604 5.021,3.281 false 0.104,1.635 0.938,2.01 0.833,0.375 10 false Exhaust Gas Pressure 3.219,1.708 4.75,2.052 1.531,0.344 10 false Atmospheric Pressure 4.479,1.229 5.729,1.688 1.25,0.458 10 false Differential Pressure Sensor 5.76,0.573 6.313,0.885 0.552,0.313 10 false ECM 5.021,2.083 6.813,2.458 1.792,0.375 10 false Gasoline Particulate Filter 0.885,6.229 2.354,6.563 1.469,0.333 10 false PM Capture Function 2.875,6.177 3.948,6.375 1.073,0.198 10 false PM, Ash 6.042,4.406 6.917,4.677 0.875,0.271 10 false PM, Ash 4.146,5.833 5.552,6.146 1.406,0.313 10 false Exhaust Gas Flow 5.615,6.229 7,6.521 1.385,0.292 10 false Ash: Metal Oxides 5.344,3.531 6.323,3.99 0.979,0.458 10 false Front Exhaust Pipe Assembly

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P244B00 Particulate Filter Differential Pressure Too High Bank 1 When it is estimated that the GPF differential pressure will increase to the limit value or more and the intake air flow does not exceed 34 gm/sec.* (1 trip detection logic).
·

Front exhaust pipe assembly (GPF)

·

Differential pressure sensor

·

Mass air flow meter

·

Wire harness or connector

·

ECM


Comes on DTC stored SAE Code: P244B

*: Varies with exhaust gas temperature

A428851E01
2.208,0.26 2.396,0.26 2.396,0.26 2.802,1.594 true 4.688,0.302 4.5,0.302 4.5,0.302 4.198,1.646 true 4.844,1.646 4.656,1.646 4.656,1.646 4.427,2.458 true 0.458,3.844 5.5,4.042 5.042,0.198 10 false : Change in angle with amount of PM and ash in GPF catalyst 0.333,4.125 5.375,4.323 5.042,0.198 10 false *1: DTC P244B00 storage and MIL illumination area 0.333,4.385 5.375,4.583 5.042,0.198 10 false *2: Vehicle Control History code X0858 or X0859 storage area 1.5,3.052 1.917,3.354 0.417,0.302 10 false Low 1.198,2.823 1.615,3.125 0.417,0.302 10 false Low 1.177,0.927 1.594,1.229 0.417,0.302 10 false High 5.75,3.083 6.167,3.385 0.417,0.302 10 false High 3.26,3.375 4.698,3.74 1.438,0.365 10 false Mass Air Flow 0.854,1.333 2.292,1.698 1.438,0.365 10 false Threshold 0.313,1.885 1.292,2.354 0.979,0.469 10 false GPF Differential Pressure 2.063,1.146 2.24,1.313 0.177,0.167 10 true *1 3.635,1.146 3.813,1.313 0.177,0.167 10 true *2 0.198,0.177 2.177,0.615 1.979,0.438 10 false Accumulated amount of PM and ash in GPF catalyst is high 4.75,0.219 7,0.667 2.25,0.448 10 false Accumulated amount of PM and ash in GPF catalyst is medium 4.906,1.573 7.146,2.021 2.24,0.448 10 false Accumulated amount of PM and ash in GPF catalyst is low

Transition of Output Power Limit
A428852E01
0.677,0.938 1.292,1.135 0.615,0.198 10 false Soft 6.115,0.938 6.729,1.135 0.615,0.198 10 false Hard 0.708,1.865 2.458,2.396 1.75,0.531 10 false Vehicle Control History code X0858 is stored 2.688,1.844 4.448,2.26 1.76,0.417 10 false Vehicle Control History code X0859 is stored 4.667,1.833 6.396,2.396 1.729,0.563 10 false DTC P244B00 is stored and MIL is illuminated

MONITOR DESCRIPTION

When particulate matter and ash accumulate in the GPF, it becomes difficult for the exhaust gas to flow and the GPF differential pressure increases, so the ECM limits the intake air flow to protect parts.

After the limit value of the intake air flow drops below the threshold, if a driving operation equal to or higher than the current load is performed and it is estimated that the GPF differential pressure will increase to the limit value or more, when the intake air flow reaches the limit value, excessive accumulation is detected in the GPF, a DTC is output and the MIL illuminates.

MONITOR STRATEGY

Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

A417745E13
2.979,3.25 2.833,3.25 2.833,3.25 2.667,2.885 false 5.406,3.25 5.531,3.25 5.531,3.25 5.688,2.885 false 0.344,2.396 2.01,2.719 1.667,0.323 10 false Power Switch on (IG) 0.479,2.688 1.719,2.885 1.24,0.198 10 false Power Switch OFF 1.333,2.115 2.25,2.313 0.917,0.198 10 false Idling 0.219,1.177 1.865,1.594 1.646,0.417 10 false 60 km/h [Engine running] 2.125,2.01 2.448,2.281 0.323,0.271 10 false [A] 2.917,1.396 3.26,1.646 0.344,0.25 10 false [B] 1.906,2.938 2.51,3.323 0.604,0.385 10 false 5 minutes or more 3.01,3.167 3.948,3.448 0.938,0.281 10 false 30 seconds 4.667,3.156 5.51,3.438 0.844,0.281 10 false 30 seconds 6.146,3.135 6.51,3.406 0.365,0.271 10 false [C] 0.771,0.042 1.844,0.24 1.073,0.198 10 false Vehicle Speed 6.615,2.813 7.115,3.042 0.5,0.229 10 false Time

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F).

6.

Turn the power switch off and wait for at least 30 seconds.

7.

Turn the power switch on (IG).

8.

Turn the GTS on.

9.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

10.

Start the engine and idle it for 5 minutes or more [A].

11.

With the engine running, repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 5 times [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


12.

Turn the power switch off and wait for at least 30 seconds.

13.

Turn the power switch on (IG).

14.

Turn the GTS on.

15.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

18.

Input the DTC: P244B00.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [A] through [C] again.




WIRING DIAGRAM

·

Refer to DTC P010012 for the mass air flow meter circuit.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P010012

·

Differential pressure sensor circuit

A421608E20
0.229,2.781 0.688,2.979 0.458,0.198 10 false C38 0.229,2.969 2.073,3.271 1.844,0.302 10 false Differential Pressure Sensor 1.135,0.938 1.448,1.135 0.313,0.198 10 false VC 1.458,0.833 1.615,1.031 0.156,0.198 10 false 3 1.188,2.24 1.5,2.438 0.313,0.198 10 false E2 1.448,2.146 1.604,2.344 0.156,0.198 10 false 1 1.073,1.583 1.531,1.781 0.458,0.198 10 false PEX 1.458,1.49 1.615,1.688 0.156,0.198 10 false 2 5.083,3 5.396,3.198 0.313,0.198 10 false C63 5.073,3.177 5.531,3.375 0.458,0.198 10 false ECM 4.656,0.844 5.271,1.042 0.615,0.198 10 false VCPX 5.51,0.635 5.969,0.833 0.458,0.198 10 false 5 V 4.344,0.844 4.656,1.042 0.313,0.198 10 false 117 4.417,1.479 4.729,1.677 0.313,0.198 10 false 86 4.656,1.5 5.115,1.698 0.458,0.198 10 false PEX 4.344,2.146 4.656,2.344 0.313,0.198 10 false 118 4.646,2.146 5.26,2.344 0.615,0.198 10 false EPEX 5.458,1.26 6.375,1.458 0.917,0.198 10 false 200 kΩ


CAUTION / NOTICE / HINT

HINT:
·

Clear the Vehicle Control History after completing repairs.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>VEHICLE CONTROL HISTORY

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244B00)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55

e.

Record the Vehicle Control History.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P244B00 is output A
DTC P244B00 and other DTCs are output B


HINT:

If any DTCs other than P244B00 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (ASH DEPOSITION RATIO)

B

2.READ VALUE USING GTS (ASH DEPOSITION RATIO)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Ash Deposition Ratio Bank1.

Powertrain > Engine > Data List
Tester Display
Ash Deposition Ratio Bank1
50003 372 822

e.

Read the value displayed on the GTS.

Standard:
GTS Display Specified Condition
Ash Deposition Ratio Bank1 Less than 100%



Result:
Proceed to
OK
NG


HINT:

Clear the GPF deterioration record using the GTS after replacing the front exhaust pipe assembly (GPF).

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



OK

3.CLEAR DTC

NG

REPLACE FRONT EXHAUST PIPE ASSEMBLY (GPF)

3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS (PM DEPOSITION RATIO)
4.READ VALUE USING GTS (PM DEPOSITION RATIO)
a.

Turn the power switch on (IG).


b.

Turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / PM Deposition Ratio Bank 1.

Powertrain > Engine > Data List
Tester Display
PM Deposition Ratio Bank1
50003 372 821

d.

Read the values displayed on the GTS.

HINT:

Data List item "PM Deposition Ratio Bank1" is necessary after performing particulate filter regenerate. Therefore, make sure check them.



Result:
Proceed to
NEXT



NEXT

5.PERFORM PM REGENERATE MODE
5.PERFORM PM REGENERATE MODE

Result:
Proceed to
NEXT



NEXT

6.READ VALUE USING GTS (PM DEPOSITION RATIO)
6.READ VALUE USING GTS (PM DEPOSITION RATIO)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / PM Deposition Ratio Bank1.

Powertrain > Engine > Data List
Tester Display
PM Deposition Ratio Bank1
50003 372 821

e.

Read the value displayed on the GTS.

Standard:
GTS Display Specified Condition
PM Deposition Ratio Bank1 Less than 30%


HINT:

After performing particulate filter regenerate, if the value of Data List items "PM Deposition Ratio Bank1" is less than the value during step 4 (READ VALUE USING GTS (PM DEPOSITION RATIO)), the driving condition may not be suitable for particulate filter regenerate. Therefore, perform particulate filter regenerate again.



Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

9.INSPECT DIFFERENTIAL PRESSURE SENSOR
7.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P244B00)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P244B00)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P244B00 is output B




A

END

B

9.INSPECT DIFFERENTIAL PRESSURE SENSOR
9.INSPECT DIFFERENTIAL PRESSURE SENSOR

Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

NG

15.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
10.READ VALUE USING GTS (MASS AIR FLOW SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed, Mass Air Flow Sensor and Coolant Temperature.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Mass Air Flow Sensor
Coolant Temperature
50003 372 211,215,205

g.

Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.


h.

Read Mass Air Flow Sensor while maintaining an engine speed of 2500 rpm.

HINT:

During charge control, the engine speed is set at idle. Therefore, the engine speed will not increase when the accelerator pedal is depressed. In this case, read the Data List after charge control has completed.


Standard:
GTS Display Condition Specified Condition
Mass Air Flow Sensor
·

Engine warmed up

·

Shift lever position: N

·

A/C: Off

·

Engine Speed: 2500 rpm


Between 4.5 and 8.5 gm/sec



Result:
Proceed to
OK
NG


HINT:

Clear the GPF deterioration record using the GTS after replacing the front exhaust pipe assembly (GPF).

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



OK

REPLACE FRONT EXHAUST PIPE ASSEMBLY

NG

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)
11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the C6 mass air flow meter connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C6-1 (+B) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - MASS AIR FLOW METER SUB-ASSEMBLY)

12.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the C6 mass air flow meter connector.


b.

Disconnect the C63 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C6-3 (VG) - C63-137 (VG) Always Below 1 Ω
C6-2 (E2G) - C63-104 (E2G) Always Below 1 Ω
C6-3 (VG) or C63-137 (VG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the C6 mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C6-2 (E2G) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.INSPECT MASS AIR FLOW METER

NG

14.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter, referring to On-vehicle Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>ON-VEHICLE INSPECTION


b.

Inspect the mass air flow meter, referring to Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION


c.

Inspect the function of the mass air flow meter.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

v.

Start the engine.


vi.

Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
50003 372 215

vii.

Check that the Mass Air Flow Sensor value changes when the engine is raced.

OK:

The reading changes.


HINT:
·

During charge control, the engine speed is set at idle. Therefore, the engine speed will not increase when the accelerator pedal is depressed. In this case, read the Data List after charge control has completed.

·

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION





Result:
Proceed to
OK
NG



OK

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
a.

Disconnect the C38 differential pressure sensor connector.


b.

Disconnect the C63 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C38-3 (VC) - C63-117 (VCPX) Always Below 1 Ω
C38-2 (PEX) - C63-86 (PEX) Always Below 1 Ω
C38-1 (E2) - C63-118 (EPEX) Always Below 1 Ω
C38-3 (VC) or C63-117 (VCPX) - Body ground and other terminals Always 10 kΩ or higher
C38-2 (PEX) or C63-86 (PEX) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.REPLACE DIFFERENTIAL PRESSURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.REPLACE DIFFERENTIAL PRESSURE SENSOR

b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

f.

Start the engine and allow it to idle until the engine coolant temperature reaches 75°C (167°F) or higher. [A]


g.

Turn the power switch off and wait for 30 seconds or more. [B]


h.

Repeat the above procedures [A] and [B] 3 times.

HINT:

Procedures [A] and [B] must be repeated 3 times to complete the differential pressure sensor learning process.



Result:
Proceed to
NEXT



NEXT

END