The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the electric power steering column sub-assembly removal/installation are shown below.
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
45130
3.REMOVE HORN BUTTON ASSEMBLY
45100
4.REMOVE STEERING WHEEL ASSEMBLY
73900
5.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
67914
6.REMOVE FRONT DOOR SCUFF PLATE LH (w/o Knee Airbag)
62112
7.REMOVE COWL SIDE TRIM BOARD LH (w/o Knee Airbag)
55606
8.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Knee Airbag)
55404D
9.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)
55470
10.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY (w/o Knee Airbag)
55434B
11.REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL (w/o Knee Airbag)
53601
12.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (w/o Knee Airbag)
55545
13.REMOVE FUSE BOX OPENING COVER (w/o Knee Airbag)
45287
14.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY
Removing the lower steering column cover sub-assembly in the incorrect order will cause the parts to break.
Release the tilt and telescopic lever and fully extend and lower the steering column assembly.
Lock the tilt and telescopic lever.
Remove the 2 screws.
|
Place Hand Here |
|
Push |
Push the upper steering column cover and disengage the 4 claws as shown in the illustration.
Disengage the 2 claws.
Release the tilt and telescopic lever and fully extend and lift the steering column assembly.
Lock the tilt and telescopic lever.
|
Place Hand Here |
|
Remove in this Direction |
Pull the lower steering column cover sub-assembly toward the rear of the vehicle to disengage the claw and remove the lower steering column cover sub-assembly.
45286B
15.REMOVE UPPER STEERING COLUMN COVER
Release the tilt and telescopic lever and fully extend and lower the steering column assembly.
Lock the tilt and telescopic lever.
|
Remove in this Direction |
Disengage the claw and separate the upper steering column cover.
Disengage the 2 claws and 4 clips to remove the upper steering column cover.
16.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).
Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed with the auxiliary battery connected and the power switch on (IG).
Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.
Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.
|
Remove in this Direction |
Disengage the 3 claws to remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.
58816B
17.REMOVE CONSOLE BOX INSERT (for LHD)
87211
18.REMOVE NO. 1 AIR DUCT (for LHD)
Remove the 2 bolts.
Disengage the 3 claws to remove the No. 1 air duct.
58817A
19.REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for RHD)
87211A
20.REMOVE NO. 2 AIR DUCT (for RHD)
Remove the 2 bolts.
Disengage the 3 claws to remove the No. 2 air duct.
84340
21.REMOVE STOP LIGHT SWITCH ASSEMBLY
45259A
22.REMOVE COLUMN HOLE COVER SILENCER SHEET
|
Remove in this Direction |
Disengage the claw and open the column hole cover silencer sheet.
|
Place Hand Here |
Disengage the 2 claws to remove the column hole cover silencer sheet.
45260
23.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
| *a | Matchmark |
Put matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.
Remove the bolt.
Separate the No. 2 steering intermediate shaft assembly from the steering gear assembly.
45260
24.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
| *a | Matchmark |
Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.
Remove the bolt.
Remove the No. 2 steering intermediate shaft assembly from the steering column assembly.
25.REMOVE STEERING COLUMN ASSEMBLY (for LHD)
Disconnect the 2 power steering ECU connectors.
Disengage the power steering ECU wire harness clamp.
Disconnect each connector and disengage each clamp from the steering column assembly.
Remove the bolt, 2 nuts and steering column assembly.
26.REMOVE STEERING COLUMN ASSEMBLY (for RHD)
Disconnect the 2 power steering ECU connectors.
Disengage the power steering ECU wire harness clamp.
Disconnect each connector and disengage each clamp from the steering column assembly.
Remove the bolt, 2 nuts and steering column assembly.