Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › KNEE AIRBAG ASSEMBLY › from 2020.08
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0303873 KNEE AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  KNEE AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the lower No. 1 instrument panel airbag assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Hide 55545 3.REMOVE FUSE BOX OPENING COVER

Hide 55470 4.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Hide 55434B 5.REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL

Hide 73900 6.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY WITH DOOR

CAUTION:
B417755C02
0.604,0.521 0.76,0.719 0.156,0.198 10 false .
V100155

Deployment Side


When storing the lower No. 1 instrument panel airbag assembly with door, keep the airbag deployment side facing upward.


a.

Check that the power switch off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B454046

Remove the 2 bolts.


d.

Disengage the hooks to separate the lower No. 1 instrument panel airbag assembly with door.

NOTICE:

When separating the lower No. 1 instrument panel airbag assembly with door, do not pull the airbag wire harness.



e.
B454047C01
0.406,2.313 0.719,2.208 true 0.604,3.094 0.99,2.469 true 1.51,1.167 1.167,0.917 true 0.188,2.229 0.5,2.385 0.313,0.156 10 false *a 0.427,3.021 0.74,3.177 0.313,0.156 10 false *b 1.542,1.094 1.854,1.25 0.313,0.156 10 false *c
*a Protective Tape
*b Airbag Connector
*c Airbag Connector Lock


Using a screwdriver with its tip wrapped in protective tape, release the airbag connector lock.


f.

Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly with door.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



Hide 73997 7.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG DOOR

a.
B460342

Disengage the hooks.


b.
B460341

Disengage the hooks to remove the lower No. 1 instrument panel airbag door from the lower No. 1 instrument panel airbag assembly.