Home › Drivetrain › P610 (HYBRID TRANSMISSION / TRANSAXLE) › OIL COOLER › from 2020.08
RM32K0E _52 Drivetrain _059722 P610 HYBRID TRANSMISSION / TRANSAXLE _0292763 OIL COOLER A

P610 HYBRID TRANSMISSION / TRANSAXLE  OIL COOLER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during motor cooling cooler removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Panoramic view monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration MIL comes on (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for Nickel Metal Hydride Battery:
(Click here)
for Lithium-ion Battery:
(Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for NICKEL METAL HYDRIDE BATTERY:

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for LITHIUM-ION BATTERY:

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444A 2.REMOVE REAR ENGINE UNDER COVER LH

Hide G9200 3.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 17705 4.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 5.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 6.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide G922H 7.DISCONNECT INLET HYBRID RADIATOR HOSE

Hide G922F 8.DISCONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE

Hide G125A 9.REMOVE MOTOR COOLING COOLER

a.
C366449

Slide the clip and disconnect the No. 1 motor cooling hose from the No. 1 motor cooling pipe.


b.
C365165

Remove the union bolt and gasket to disconnect the No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.


c.

Remove the bolt and No. 1 oil cooler tube clamp from the hose bracket.


d.
C365172

Slide the clip and remove the No. 2 motor cooling pipe from the No. 2 motor cooling hose.


e.
C365173

Remove the 3 bolts and motor cooling cooler from the hybrid vehicle transaxle assembly.

NOTICE:

Make sure not to remove the No. 1 motor cooling hose and No. 2 motor cooling hose from the motor cooling cooler as the motor cooling cooler may be deformed.