Home › Engine / Hybrid System › CRUISE CONTROL › LANE TRACING ASSIST SYSTEM › from 2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0440929 LANE TRACING ASSIST SYSTEM C

CRUISE CONTROL  LANE TRACING ASSIST SYSTEM  U023587  Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message  


DESCRIPTION

The forward recognition camera and millimeter wave radar sensor assembly communicate via CAN communication. If there is an error in the communication with the millimeter wave radar sensor assembly, the forward recognition camera stores DTC U023587.

DTC No. Detection Item DTC Detection Condition Trouble Area
U023587 Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message When the power switch is on (IG) for 3 seconds or more, a communication data malfunction between the forward recognition camera and the millimeter wave radar sensor assembly continues for approximately 2 seconds or more.
·

Wire harness and connector

·

Forward Recognition Camera

·

Millimeter Wave Radar Sensor Assembly



Pattern DTC output part name
(Display on GTS)
Suspected Area
(Malfunction Status)
Forward Recognition Camera Millimeter Wave Radar Sensor Assembly
Lane Control Forward Recognition Camera (Front Lighting Control) Pre-Collision System Radar Cruise2
U023587 U023587 U023A87 U023A87

○: DTC is output

-: DTC is not output

Pattern1 ○ ○ ○ ○ Harness or connector (Open or short)
Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)
Pattern2 ○ ○ - - Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)

HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.


WIRING DIAGRAM

C424985E09
4.594,1.031 4.906,1.229 0.313,0.198 10 false A2 4.583,1.198 7.156,1.448 2.573,0.25 10 false Millimeter Wave Radar Sensor Assembly 0.292,1.073 0.635,1.281 0.344,0.208 10 false R5 5.49,0.854 5.938,1 0.448,0.146 10 false CA1N 0.302,1.25 2.49,1.573 2.188,0.323 10 false Forward Recognition Camera 5.281,0.188 5.625,0.396 0.344,0.208 10 false 5 5.271,0.635 5.594,0.833 0.323,0.198 10 false 6 5.49,0.188 5.938,0.333 0.448,0.146 10 false CA1P 1,0.188 1.448,0.333 0.448,0.146 10 false CANH 1,0.833 1.448,0.979 0.448,0.146 10 false CANL 1.49,0.667 1.833,0.875 0.344,0.208 10 false 12 1.5,0.177 1.844,0.385 0.344,0.208 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT


·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.

HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT


·

After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

If there are communication malfunctions for systems other than the forward recognition camera and millimeter wave radar sensor assembly, refer to "HOW TO PROCEED WITH TROUBLESHOOTING" for the CAN Communication System.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK FOR DTC
a.

Read each DTC and check the diagnosis pattern using the table below.

Chassis > Lane Control > Trouble Codes
50001 418
Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433
Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Powertrain > Radar Cruise2 > Trouble Codes
50001 426

Pattern DTC output part name
(Display on GTS / Output DTC)
Lane Control Forward Recognition Camera (Front Lighting Control) Pre-Collision System Radar Cruise2
Pattern 1 U023587 U023587 U023A87 U023A87
Pattern 2 U023587 U023587 - -

Result:
Result Proceed to
Pattern 1 A
Pattern 2 B



A

2.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)

B

4.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
2.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the R5 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-6 (CANH) - R5-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
R5-6 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R5-12 (CANL) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R5-6 (CANH) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R5-12 (CANL) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

3.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
3.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A2 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-5 (CA1P) - A2-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A2-5 (CA1P) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A2-6 (CA1N) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A2-5 (CA1P) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A2-6 (CA1N) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS SUB LINE OR CONNECTOR

4.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Disconnect the R5 forward recognition camera connector.


b.

Using an oscilloscope, check the waveform.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
R5-6 (CANH) - R5-12 (CANL) Power switch on (IG) 1V/DIV., 100μs./DIV. Waveform generation


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY