Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2020.08
RM32K0E _58 Vehicle Interior _061839 PRE-COLLISION _0303861 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U023A87  Lost Communication with Image Processing Module "A" Missing Message  


DESCRIPTION

The millimeter wave radar sensor assembly is connected to the forward recognition camera via the CAN communication line. If the millimeter wave radar sensor assembly receives signals indicating that its communication with the forward recognition camera is abnormal, the millimeter wave radar sensor assembly stores DTC U023A87.

DTC No. Detection Item DTC Detection Condition Trouble Area
U023A87 Lost Communication with Image Processing Module "A" Missing Message When the power switch is on (IG) for 3 seconds or more, a forward recognition camera communication malfunction continues for approximately 3 seconds or more.
·

Forward recognition camera

·

Millimeter wave radar sensor assembly



Pattern DTC output part name
(Display on GTS)
Suspected Area (Malfunction Status)
Millimeter Wave Radar Sensor Assembly Forward Recognition Camera
Pre-Collision System Radar Cruise2 Lane Control Forward Recognition Camera (Front Lighting Control)
U023A87 U023A87 U023587 U023587

○: DTC is output

-: DTC is not output

Pattern 1 ○ ○ ○ ○ Harness or connector (Open or short)
Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)
Pattern 2 ○ ○ - - Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)

HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.


WIRING DIAGRAM

C424985E11
5.333,1.073 5.646,1.271 0.313,0.198 10 false A2 5.333,1.229 6.74,1.625 1.406,0.396 10 false Millimeter Wave Radar Sensor Assembly 0.552,1.104 0.896,1.313 0.344,0.208 10 false R5 5.49,0.854 5.917,1.052 0.427,0.198 10 false CA1N 0.542,1.26 1.813,1.677 1.271,0.417 10 false Forward Recognition Camera 5.281,0.188 5.625,0.396 0.344,0.208 10 false 5 5.271,0.635 5.594,0.833 0.323,0.198 10 false 6 5.49,0.167 5.927,0.365 0.438,0.198 10 false CA1P 1,0.188 1.448,0.333 0.448,0.146 10 false CANH 1,0.833 1.448,0.979 0.448,0.146 10 false CANL 1.49,0.667 1.833,0.875 0.344,0.208 10 false 12 1.5,0.177 1.844,0.385 0.344,0.208 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.

HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT


·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera adjustment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT


·

After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal. Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery. Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

If there are communication malfunctions for systems other than the millimeter wave radar sensor assembly and forward recognition camera, refer to "HOW TO PROCEED WITH TROUBLESHOOTING" for the CAN Communication System.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK FOR DTC
a.

Read each DTC and check the diagnosis pattern using the table below.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Powertrain > Radar Cruise2 > Trouble Codes
50001 426
Chassis > Lane Control > Trouble Codes
50001 418
Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433

Pattern DTC output part name
(Display on GTS / Output DTC)
Radar Cruise2 Pre-Collision System Lane Control Forward Recognition Camera (Front Lighting Control)
Pattern 1 U023A87 U023A87 U023587 U023587
Pattern 2 U023A87 U023A87 - -

Result:
Result Proceed to
Pattern 1 A
Pattern 2 B



A

2.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

B

4.CHECK FORWARD RECOGNITION CAMERA
2.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A2 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-5 (CA1P) - A2-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A2-5 (CA1P) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A2-6 (CA1N) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A2-5 (CA1P) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A2-6 (CA1N) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

3.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)
3.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the R5 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-6 (CANH) - R5-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
R5-6 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R5-12 (CANL) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R5-6 (CANH) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R5-12 (CANL) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE CAN BUS SUB LINE OR CONNECTOR

4.CHECK FORWARD RECOGNITION CAMERA
a.

Disconnect the A2 millimeter wave radar sensor assembly connector.


b.

Measure the waveform according the table below.

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
A2-5 (CA1P) - A2-6 (CA1N) Power switch on (IG) 1V/DIV., 100μs./DIV. Waveform generation


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPLACE FORWARD RECOGNITION CAMERA