The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during battery voltage sensor removal/installation are shown below.
Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>PRECAUTION
Be sure to wear insulating gloves when working on high voltage wiring or components.
If work is performed without wearing insulating gloves, there is a danger of electric shock.
The type of battery voltage sensor to be used varies depending on the vehicle model.
| *a | Bluish green Label |
The type of battery voltage sensor can be confirmed by the color of the label.
If the wrong type of battery voltage sensor is installed, the power switch cannot be turned on (READY).
After installing the battery voltage sensor, perform the following to check that the power switch can be turned on (READY).
Turn the power switch on (READY).
Turn the power switch off and wait for 30 seconds or more.
Turn the power switch on (READY) again.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
G3834
2.REMOVE SERVICE PLUG GRIP
82121
3.DISCONNECT ENGINE WIRE
4.REMOVE CONNECTOR COVER ASSEMBLY
5.CHECK TERMINAL VOLTAGE
6.INSTALL CONNECTOR COVER ASSEMBLY
82121
7.CONNECT ENGINE WIRE
73350C
8.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
9.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY
72693
10.REMOVE REAR SEAT CUSHION LOCK HOOK
67918A
11.REMOVE REAR DOOR SCUFF PLATE LH
76974F
12.REMOVE REAR UNDER SIDE COVER LH
67917A
13.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
76973F
14.REMOVE REAR UNDER SIDE COVER RH
Use the same procedure as for the LH side.
76971G
15.REMOVE REAR UNDER COVER
71033
16.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY
G9230
17.REMOVE BATTERY COOLING BLOWER ASSEMBLY
G92N4A
18.REMOVE NO. 1 HV BATTERY COVER PANEL RH
821H1
19.DISCONNECT HV FLOOR UNDER WIRE
82161
20.DISCONNECT FLOOR WIRE
G92PC
21.REMOVE NO. 1 HV BATTERY PROTECTOR
82161
22.DISCONNECT FLOOR WIRE
G920L
23.REMOVE UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY
Be sure to wear insulated gloves and protective goggles.
Remove the 5 bolts.
Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.
To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.
If the HV battery has been struck or dropped, replace it.
Move the HV battery toward the front of the vehicle.
Remove the 7 bolts, 6 nuts and upper No. 1 hybrid battery cover sub-assembly from the HV battery.
G92Q1
24.REMOVE NO. 1 HV BATTERY SHIELD PANEL
Be sure to wear insulated gloves and protective goggles.
Disengage the clamp.
Disconnect the battery voltage sensor connector.
Remove the bolt and 2 nuts.
| *1 | No. 1 HV Battery Shield Panel |
| *2 | Rear Hybrid Battery Shield Sub-assembly |
|
Pull Back |
Pull back the rear hybrid battery shield sub-assembly and remove the No. 1 HV battery shield panel from the HV battery.
Pull back the rear hybrid battery shield sub-assembly until it is separated from the stud bolt of the No. 1 HV battery shield panel.
89892A
25.REMOVE BATTERY VOLTAGE SENSOR
Be sure to wear insulated gloves and protective goggles.
Disconnect the battery voltage sensor connector.
Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.
Remove the bolt and battery voltage sensor from the HV battery.
If the battery voltage sensor has been struck or dropped, replace it.