Home › Engine / Hybrid System › 2ZR-FXE (INTAKE / EXHAUST) › EXHAUST MANIFOLD › from 2020.08
RM32K0E _51 Engine / Hybrid System _059910 2ZR-FXE INTAKE / EXHAUST _0293911 EXHAUST MANIFOLD A

2ZR-FXE INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold (TWC: Front Catalyst) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of air fuel ratio sensor

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 51441 2.REMOVE NO. 1 ENGINE UNDER COVER

Hide 58166 3.REMOVE FRONT FLOOR COVER LH

a.
A393190C01
0,0 0,0 false
V100135

Bolt
V100136

Clip


Remove the 2 bolts and clip and disengage the 5 clamps to remove the front floor cover LH from the vehicle body.


Hide 58165B 4.REMOVE FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the front floor cover LH.


Hide 57533B 5.REMOVE FRONT FLOOR CENTER BRACE (for GR SPORT)

a.
A450891

Remove the 12 bolts and 2 front floor center braces from the vehicle body.


Hide 57533B 6.REMOVE FRONT FLOOR CENTER BRACE (except GR SPORT)

a.
A393191

Remove the 12 bolts and 3 front floor center braces from the vehicle body.


Hide 17410 7.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A378756

Disconnect the heated oxygen sensor connector.


b.

Disengage the wire harness clamp.


c.
A393192

Remove the 4 bolts and 4 compression springs and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold (TWC: Front Catalyst) and tail exhaust pipe assembly.


d.

Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the 2 exhaust pipe supports.


e.

Remove the 2 exhaust pipe gaskets from the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).


Hide 8.REMOVE WIRING HARNESS CLAMP BRACKET (w/o Differential Pressure Sensor)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A376894

Disengage the clamp and remove the bolt and wiring harness clamp bracket from the cylinder head sub-assembly.


b.
A393395

Disengage the 3 clamps and remove the bolt and wiring harness clamp bracket from the front suspension crossmember sub-assembly.


Hide 25715 9.REMOVE EMISSION CONTROL VALVE BRACKET (w/ Differential Pressure Sensor)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A459682

Disengage the wire harness clamp.


b.

Disconnect the differential pressure sensor connector.


c.
A459676

Slide the clip and disconnect the vacuum transmitting hose assembly from the No. 1 pipe.


d.

Remove the bolt and emission control valve bracket from the cylinder head sub-assembly.


Hide 25733A 10.REMOVE NO. 1 PIPE (w/ Differential Pressure Sensor)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A459678

Remove the nut.


b.

Remove the No. 1 pipe from the exhaust manifold.


Hide 17167 11.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.

w/o Differential Pressure Sensor:

i.
A376897

Remove the 6 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.



b.

w/ Differential Pressure Sensor:

i.
A459677

Remove the 4 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.



Hide 17168 12.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A395539

Remove the 4 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold (TWC: Front Catalyst).


Hide 17118 13.REMOVE MANIFOLD STAY

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A395537

Remove the 3 bolts and manifold stay from the exhaust manifold (TWC: Front Catalyst) and cylinder block sub-assembly.


Hide 17141 14.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A459680C01
0.083,0.115 0.438,0.354 0.354,0.24 12 false *A 0.094,2.479 0.375,2.729 0.281,0.25 12 false *B
*A w/o Differential Pressure Sensor
*B w/ Differential Pressure Sensor


Remove the 7 nuts and exhaust manifold (TWC: Front Catalyst) from the cylinder head sub-assembly.


b.
A376909C01
2.188,1.438 2.063,1.438 2.063,1.438 1.969,1.01 true 0.26,1.344 0.417,1.344 0.417,1.344 0.521,0.906 true 2.208,1.354 2.438,1.573 0.229,0.219 10 true *1 0.083,1.26 0.271,1.458 0.188,0.198 10 true *2
*1 Exhaust Manifold To Head Gasket
*2 EGR Cooler Gasket


Remove the exhaust manifold to head gasket and EGR cooler gasket from the cylinder head sub-assembly.