Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2020.08–2022.01
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Electric Parking Brake ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Electric Parking Brake ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Electric Parking Brake" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Electric Parking Brake" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Electric Parking Brake" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Electric Parking Brake ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Brake actuator assembly branch line or connector

·

Power source circuit of brake actuator assembly

·

Brake actuator assembly ground circuit

·

Brake actuator assembly



WIRING DIAGRAM

for LHD


C392585E01
0.146,1.594 0.76,1.792 0.615,0.198 10 false F116 0.135,1.771 2.281,2.063 2.146,0.292 10 false No. 4 CAN Junction Connector 2.229,2.354 3.729,2.625 1.5,0.271 10 false from Auxiliary Battery 2.24,3.344 3.625,3.583 1.385,0.24 10 false from IG1-NO. 1 Relay 4.354,3.521 5.385,3.74 1.031,0.219 10 false ECU-IG1 NO. 1 4.469,2.51 5.24,2.76 0.771,0.25 10 false EPB NO. 1 5.813,2.344 6.427,2.542 0.615,0.198 10 false BEPB 5.813,3.333 6.125,3.531 0.313,0.198 10 false IG 5.802,4.25 6.417,4.448 0.615,0.198 10 false EGND 5.406,4.771 5.865,4.969 0.458,0.198 10 false A85 5.396,4.948 7.031,5.177 1.635,0.229 10 false Brake Actuator Assembly 5.813,0.615 6.427,0.813 0.615,0.198 10 false CANH 5.813,1.156 6.427,1.354 0.615,0.198 10 false CANL 5.573,2.24 5.729,2.438 0.156,0.198 10 false 9 5.51,3.24 5.823,3.438 0.313,0.198 10 false 26 5.583,4.146 5.74,4.344 0.156,0.198 10 false 2 5.521,0.51 5.833,0.708 0.313,0.198 10 false 12 5.531,1.063 5.844,1.26 0.313,0.198 10 false 11 1.656,0.521 1.813,0.719 0.156,0.198 10 false 2 1.635,1.052 1.948,1.25 0.313,0.198 10 false 12


for RHD


C392585E02
2.229,3.354 3.552,3.573 1.323,0.219 10 false from IG1-NO. 1 Relay 2.26,2.333 3.656,2.583 1.396,0.25 10 false from Auxiliary Battery 4.479,2.542 5.313,2.792 0.833,0.25 10 false EPB NO. 1 4.375,3.51 5.365,3.76 0.99,0.25 10 false ECU-IG1 NO. 1 5.813,4.25 6.427,4.448 0.615,0.198 10 false EGND 5.813,2.344 6.427,2.542 0.615,0.198 10 false BEPB 5.813,3.354 6.115,3.615 0.302,0.26 10 false IG 5.802,0.625 6.417,0.823 0.615,0.198 10 false CANH 5.802,1.156 6.417,1.354 0.615,0.198 10 false CANL 0.094,1.573 0.708,1.771 0.615,0.198 10 false F118 0.094,1.74 2.063,1.958 1.969,0.219 10 false No. 5 CAN Junction Connector 1.677,0.49 1.833,0.688 0.156,0.198 10 false 6 1.656,1.052 1.969,1.25 0.313,0.198 10 false 16 5.521,0.521 5.833,0.719 0.313,0.198 10 false 12 5.531,1.063 5.844,1.26 0.313,0.198 10 false 11 5.594,2.24 5.75,2.438 0.156,0.198 10 false 9 5.521,3.24 5.833,3.438 0.313,0.198 10 false 26 5.583,4.135 5.74,4.333 0.156,0.198 10 false 2 5.438,4.771 5.896,4.969 0.458,0.198 10 false A84 5.427,4.917 7.083,5.156 1.656,0.24 10 false Brake Actuator Assembly


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C393503C04
1.833,0.333 2.25,0.583 0.417,0.25 5.083,0.333 5.5,0.583 0.417,0.25 2.469,2.219 1.854,1.51 true 1.25,2.24 1.729,1.542 true 4.635,2.24 4.958,1.552 true 5.417,2.219 5.104,1.521 true 0.156,0.115 0.375,0.354 0.219,0.24 10 false *a 2.354,0.375 2.615,0.563 0.26,0.188 10 false *B 1.917,0.375 2.229,0.573 0.313,0.198 10 false A84 5.177,0.375 5.49,0.573 0.313,0.198 10 false A85 5.604,0.375 5.865,0.563 0.26,0.188 10 false *A 1.073,2.281 1.688,2.479 0.615,0.198 10 false CANL 2.302,2.281 2.917,2.479 0.615,0.198 10 false CANH 4.479,2.281 5.094,2.479 0.615,0.198 10 false CANL 5.229,2.281 5.844,2.479 0.615,0.198 10 false CANH
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Brake actuator assembly)
- -


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A85-12 (CANH) - A85-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

for RHD
Tester Connection Condition Specified Condition
A84-12 (CANH) - A84-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the brake actuator assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

C393503C06
1.833,0.333 2.25,0.583 0.417,0.25 5.083,0.333 5.5,0.583 0.417,0.25 2.135,2.229 1.396,1.406 true 5.375,2.208 4.688,1.427 true 0.156,0.115 0.375,0.354 0.219,0.24 10 false *a 2.354,0.375 2.615,0.563 0.26,0.188 10 false *B 1.917,0.375 2.229,0.573 0.313,0.198 10 false A84 5.177,0.375 5.49,0.573 0.313,0.198 10 false A85 5.604,0.375 5.865,0.563 0.26,0.188 10 false *A 1.958,2.281 2.573,2.479 0.615,0.198 10 false EGND 5.229,2.281 5.844,2.479 0.615,0.198 10 false EGND
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Brake actuator assembly)
- -


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A85-2 (EGND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A84-2 (EGND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

C393503C07
1.833,0.333 2.25,0.583 0.417,0.25 5.083,0.333 5.5,0.583 0.417,0.25 3.344,2.24 2.698,1.448 true 6.323,2.229 5.958,1.427 true 1.958,2.24 2.417,1.625 true 5.229,2.219 5.656,1.635 true 0.156,0.115 0.375,0.354 0.219,0.24 10 false *a 2.354,0.375 2.615,0.563 0.26,0.188 10 false *B 1.917,0.375 2.229,0.573 0.313,0.198 10 false A84 5.177,0.375 5.49,0.573 0.313,0.198 10 false A85 5.604,0.375 5.865,0.563 0.26,0.188 10 false *A 3.208,2.281 3.823,2.479 0.615,0.198 10 false BEPB 6.125,2.281 6.74,2.479 0.615,0.198 10 false BEPB 1.875,2.281 2.198,2.5 0.323,0.219 10 false IG 5.156,2.281 5.396,2.479 0.24,0.198 10 false IG
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Brake actuator assembly)
- -


Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A85-9 (BEPB) - Body ground Power switch off 11 to 14 V
A85-26 (IG) - Body ground Power switch on (IG) 11 to 14 V

for RHD
Tester Connection Switch Condition Specified Condition
A84-9 (BEPB) - Body ground Power switch off 11 to 14 V
A84-26 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)