Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO RECEIVER (for Radio and Display Type) › 2020.08–2022.01
RM32K0E _56 Audio / Visual / Telematics _061817 AUDIO / VIDEO _0303529 RADIO RECEIVER(for Radio and Display Type) A

AUDIO / VIDEO  RADIO RECEIVER(for Radio and Display Type)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the radio and display receiver assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

CAUTION:
B458500

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS.

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1


-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55470 3.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Hide 55406B 4.REMOVE INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY

Hide 55670A 5.REMOVE INSTRUMENT PANEL CENTER REGISTER ASSEMBLY

Hide 86140A 6.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET

a.
E362283

Remove the 4 screws.


b.
E429954C01
0,0 0,0 false
V113147

Remove in this Direction


Pull the radio and display receiver assembly with bracket toward the rear of the vehicle to disengage the claws and clips as shown in the illustration.


c.

Disconnect each connector and remove the radio and display receiver assembly with bracket.


Hide 55405B 7.REMOVE INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY

a.
E395577

Disengage the claws to remove the instrument cluster finish center panel sub-assembly.


Hide 86211J 8.REMOVE NO. 1 RADIO RECEIVER BRACKET

a.
E395922

Remove the 2 screws and No. 1 radio receiver bracket from the radio and display receiver assembly.


Hide 86212C 9.REMOVE NO. 2 RADIO RECEIVER BRACKET

a.
E395578

Remove the 2 screws and No. 2 radio receiver bracket from the radio and display receiver assembly.