Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION ECU › 2020.08–2022.01
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0299561 NAVIGATION ECU A

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION ECU  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the navigation ECU removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedures not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS.

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1


-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55470 3.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Hide 67914 4.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH

Hide 55606 6.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55434B 7.REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL

Hide 55440D 8.REMOVE INSTRUMENT PANEL BOX ASSEMBLY

Hide 55406B 9.REMOVE INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY

Hide 86841 10.REMOVE NAVIGATION ECU WITH BRACKET (for TMMT Made)

a.
E426201

Disconnect the 3 connectors.


b.

Remove the 2 nuts.


c.

Pull out and remove the navigation ECU with bracket.


Hide 86841 11.REMOVE NAVIGATION ECU WITH BRACKET (for TMC Made)

a.
E426302

Disconnect the 3 connectors.


b.

Remove the 2 nuts.


c.
E426303

Pull out and remove the navigation ECU with bracket.


d.

Disconnect the connector.


Hide 86101M 12.REMOVE ANTENNA CORD SUB-ASSEMBLY (for TMC Made)

a.
E426485

Disconnect the 2 connectors.


b.
E426304

Disengage the clamps to remove the antenna cord sub-assembly.


Hide 86844A 13.REMOVE NO. 1 NAVIGATION ECU BRACKET (for TMMT Made)

E426202

a.

Remove the 2 bolts.


b.

Disengage the guide to remove the No. 1 navigation ECU bracket from the navigation ECU.


Hide 86844A 14.REMOVE NO. 2 NAVIGATION ECU BRACKET (for TMMT Made)

a.
E426203

Remove the 2 bolts.


b.

Disengage the guide to remove the No. 2 navigation ECU bracket from the navigation ECU.


Hide 86457 15.REMOVE NO. 1 MULTI-MEDIA MODULE BRACKET (for TMC Made)

a.
E426306

Remove the 2 bolts.


b.

Disengage the guides to remove the No. 1 multi-media module bracket from the navigation ECU.


Hide 86457A 16.REMOVE NO. 2 MULTI-MEDIA MODULE BRACKET (for TMC Made)

E426305

a.

Remove the 2 bolts.


b.

Disengage the guides to remove the No. 2 multi-media module bracket from the navigation ECU.