Home › Brake › BRAKE (FRONT) › FRONT BRAKE (for TMC Made) › from 2020.08
RM32K0E _54 Brake _060046 BRAKE (FRONT) _0407343 FRONT BRAKE(for TMC Made) A

BRAKE (FRONT)  FRONT BRAKE(for TMC Made)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the brake caliper piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system will be activated when the brake pedal is depressed or any door courtesy switch turns on. Therefore, disconnect the auxiliary battery to prevent the brake control system from being activated.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.
C365979C01
1.875,1.021 2.635,0.854 2.635,0.854 1.865,0.948 true 2.708,0.76 3.021,0.917 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks of the front disc and front axle hub sub-assembly, and install the front disc.

NOTICE:

When replacing the front disc with a new one, select the installation position where the front disc has minimal runout.



Hide 47722 2.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING

a.

Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)


Hide 3.INSTALL FRONT DISC BRAKE BUSHING DUST BOOT

a.
C344534C02
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots.

HINT:

Apply more than 0.3 g (0.01 oz.) of lithium soap base glycol grease to each front disc brake bushing dust boot.



b.

Install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.


Hide 4.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C369849C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the front disc brake cylinder slide pin (lower side).


b.

Install a new front disc brake cylinder slide bushing to the front disc brake cylinder slide pin (lower side).


c.
C369850C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the 2 front disc brake cylinder slide pins.


d.

Install the 2 front disc brake cylinder slide pins to the front disc brake cylinder mounting.


e.

Push each front disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.


Hide 5.INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE

a.

Install the 4 front disc brake pad support plates to the front disc brake cylinder mounting.

NOTICE:
·

Be sure to install each front disc brake pad support plate in the correct position and direction.

·

When reusing the brake pad support plates, use the identification marks created during removal to install them to the original positions.




Hide 04945 6.INSTALL FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

Hide 7.INSTALL FRONT DISC BRAKE PAD

a.

Install the 2 front disc brake pads to the front disc brake cylinder mounting.

NOTICE:
·

Keep the friction surfaces of the front disc brake pads and front disc free from oil and grease.

·

Install the front disc brake pad so that the pad wear indicator plate is mounted on the upper side of the vehicle.




Hide 47750 8.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY

a.

Hold each front disc brake cylinder slide pin and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 47313J 9.CONNECT FRONT FLEXIBLE HOSE

a.

Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Install the front flexible hose lock securely into the lock hole in the front disc brake cylinder assembly.



Hide 10.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION


c.

Perform the following procedure if air bleeding is not necessary:

i.

Turn the power switch on (READY).


ii.

Depress the brake pedal and release it.




Hide 11.BLEED BRAKE LINE

Hide 12.INSTALL FRONT WHEEL

Hide 13. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART