Home › General › MAINTENANCE › REAR DISC BRAKE PAD (for TMMT Made) › from 2020.08
RM32K0E _V1 General _059911 MAINTENANCE _0407402 REAR DISC BRAKE PAD(for TMMT Made) A

MAINTENANCE  REAR DISC BRAKE PAD(for TMMT Made)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear disc brake pad removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link

*1: The vehicle height changes because of suspension or tire replacement.

Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Panoramic view monitor system (Click here)

NOTICE:
·

When removing or installing the front disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.PERFORM REAR BRAKE PAD REPLACEMENT MODE

Hide 2.DISABLE BRAKE CONTROL

a.

Wait at least 2 minutes after turning the power switch off.

NOTICE:

When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



b.
C369993C01
0.052,0.052 0.354,0.302 0.302,0.25 12 true *A 0.083,2.313 0.385,2.531 0.302,0.219 12 true *B
*A for LHD
*B for RHD


Disconnect the reservoir level switch connector.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal.



d.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.


e.

Check that the brake pedal cannot be further depressed.


Hide 3.REMOVE REAR WHEEL

Hide 4.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 04466 5.REMOVE REAR DISC BRAKE PAD

CAUTION:
·
C368019

After lifting up the rear disc brake cylinder assembly, secure it in place before performing any work on it.

·

The rear disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.



a.
C399528

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.


b.
C399529C01
2.75,2.177 3.063,2.333 0.313,0.156 10 false *a 2.427,0.802 2.74,0.958 0.313,0.156 10 false *b
*a Hold
*b Turn


Hold the rear disc brake cylinder slide pin, and remove the bolt.


c.
C399530

Pull the rear disc brake cylinder assembly upward.


d.

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.


Hide 04946 6.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

a.

Remove the rear disc brake anti-squeal shim from each rear disc brake pad.