Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL SYSTEM › from 2020.08
RM32K0E _51 Engine / Hybrid System _060063 2ZR-FXE FUEL _0294215 FUEL SYSTEM L

2ZR-FXE FUEL  FUEL SYSTEM  PRECAUTION  


CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

Because the weight of the fuel tank sub-assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the components could fall down.



PRECAUTION


NOTICE:
·

Keep fuel away from rubber or leather parts.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Make sure the engine coolant temperature is 60°C (140°F) or less when performing this procedure.

·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



a.

When discharging fuel system pressure by disconnecting the C/OPN relay:

i.

Remove the No. 2 relay block cover.


ii.

Remove the C/OPN relay.


iii.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


iv.

Start the engine. After the engine has stopped on its own, turn the power switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



v.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P017100 (System Too Lean), P160400 (Startability Malfunction), P160500 (Rough Idling), P319000 (Poor Engine Power), P319100 (Engine does not Start) or P319300 (Fuel Run Out) may be stored. Clear the DTCs before proceeding to the next step.




vi.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


vii.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>REMOVAL

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



viii.

Install the C/OPN relay.


ix.

Install the No. 2 relay block cover.



b.

When discharging fuel system pressure by disconnecting the fuel pump connector:

i.

Disconnect the rear center seat outer belt assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


ii.

Remove the bench type rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


iii.

Remove the rear seat cushion lock hook.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


iv.

Remove the No. 8 wiring harness protector from the rear floor service hole cover.


v.
A374315C02
0.823,0.75 0.948,0.75 0.948,0.75 1.281,0.5 true 0.625,0.667 0.813,0.833 0.188,0.167 10 true *a
*a Protective Tape


Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.


vi.
A374318

Disconnect the fuel suction tube with pump and gauge assembly connector.


vii.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


viii.

Start the engine. After the engine has stopped on its own, turn the power switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



ix.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P017100 (System Too Lean), P160400 (Startability Malfunction), P160500 (Rough Idling), P319000 (Poor Engine Power), P319100 (Engine does not Start) or P319300 (Fuel Run Out) may be stored. Clear the DTCs before proceeding to the next step.




x.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


xi.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>REMOVAL

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



xii.

Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.


xiii.

Clean the installation surfaces of the rear floor service hole cover and vehicle body.


xiv.

Connect the fuel suction tube with pump and gauge assembly connector.


xv.

Install the rear floor service hole cover with new butyl tape.


xvi.

Install a new No. 8 wiring harness protector to the rear floor service hole cover.


xvii.

Install the rear seat cushion lock hook.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>INSTALLATION


xviii.

Install the bench type rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>INSTALLATION


xix.

Connect the rear center seat outer belt assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>INSTALLATION




FUEL LINE


a.

When disconnecting a high-pressure fuel line, a large amount of fuel will spray. Perform the following procedure:

i.

Discharge fuel system pressure.


ii.

Disconnect the fuel tube.


iii.

Drain the fuel remaining inside the fuel tube into a container.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



b.

Quick Type A:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A310731C02
1.031,0.375 1.344,0.531 0.313,0.156 10 false *a
*a Open
V100136

Pull


Open the cover of the fuel pipe clamp and remove the fuel pipe clamp from the fuel tube connector.


ii.

Check that there is no foreign matter around the fuel tube connector before disconnecting it. Clean it if necessary.


iii.
A314711C01
2.385,1.615 2.875,1.99 2.875,1.99 2.646,1.604 false 2.24,3.01 2.375,3.01 2.375,3.01 2.438,3.417 false 2.677,3.5 2.865,3.042 2.865,3.042 2.979,3.042 false 2.375,4.188 2.375,3.979 false 1.667,4.292 2.063,4.292 2.063,4.292 2.063,3.813 false 1.896,4.292 1.896,3.802 false 1,2.979 1.146,2.979 1.146,2.979 1.365,3.458 false 2.927,1.958 3.24,2.115 0.313,0.156 10 false *a 1.5,4.219 1.813,4.375 0.313,0.156 10 false *b 2.302,4.208 2.615,4.365 0.313,0.156 10 false *c 3.021,2.969 3.333,3.125 0.313,0.156 10 false *d 0.833,2.896 1.146,3.052 0.313,0.156 10 false *e 2.083,2.927 2.396,3.083 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe
*e Nylon Tube
V100135

Pinch
V100136

Pull off


Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



iv.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




v.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


vi.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



c.

Quick Type A:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A303841C01
1.542,1.563 1.698,1.76 0.156,0.198 10 false .
V100135

Pull


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Install the fuel pipe clamp to the fuel tube connector and close the cover of the fuel pipe clamp.




d.

Quick Type B:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A310728C03
0.854,3.063 1.073,3.063 1.073,3.063 1.26,2.854 false 2.052,2.75 2.417,2.75 false 0.688,2.979 1,3.135 0.313,0.156 10 false *a 1.885,2.667 2.198,2.823 0.313,0.156 10 false *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the fuel tube connector.


ii.
A310289C03
1.979,1.729 1.979,1.302 false 1.656,1.74 2.135,1.74 2.135,1.74 2.135,1.313 false 2.875,1.729 2.875,1.531 2.875,1.531 2.583,1.25 false 2.542,0.917 2.708,0.49 2.708,0.49 2.802,0.49 false 2.052,0.427 2.219,0.427 2.219,0.427 2.375,0.844 false 2.833,0.396 3.146,0.552 0.313,0.156 10 false *a 1.49,1.646 1.802,1.802 0.313,0.156 10 false *b 1.896,0.333 2.208,0.49 0.313,0.156 10 false *c 2.792,1.75 3.021,1.906 0.229,0.156 10 false *d
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe


If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).



iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



e.

Quick Type B:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A310729C03
0.844,3.094 1.031,3.094 1.031,3.094 1.271,2.844 false 2.021,2.75 2.406,2.75 false 0.677,3 0.99,3.156 0.313,0.156 10 false *a 1.844,2.656 2.156,2.813 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe and push them together. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

Connect the fuel lines and push in the retainer. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




f.

Quick Type C:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A318103C08
0.698,2.625 0.854,2.625 0.854,2.625 1.042,3.135 false 0.24,3.021 0.375,3.021 0.375,3.021 0.51,3.333 false 0.99,4.021 0.99,3.75 false 2.146,1.844 2.417,1.844 false 1.865,3.906 1.865,3.583 false 2.771,3.177 2.823,2.865 2.823,2.865 2.938,2.865 false 1.688,3.594 1.688,3.906 1.688,3.906 2.208,3.906 false 2.146,1.573 2.417,1.573 false 2.865,1.563 3.135,1.563 false 1.969,1.76 2.281,1.917 0.313,0.156 10 false *a 0.063,2.948 0.375,3.104 0.313,0.156 10 false *b 3,2.792 3.313,2.948 0.313,0.156 10 false *c 0.906,4.052 1.219,4.208 0.313,0.156 10 false *d 2.25,3.833 2.563,3.99 0.313,0.156 10 false *e 0.521,2.542 0.833,2.698 0.313,0.156 10 false *a 3.198,1.5 3.375,1.677 0.177,0.177 10 false *f 2,1.5 2.177,1.677 0.177,0.177 10 false *f
*a Retainer
*b Fuel Pipe
*c Nylon Tube
*d Fuel Tube Connector
*e O-ring
*f Claw
V100135

Push
V100136

Pull out
V100137

Pull off


Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tube connector from the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



g.

Quick Type C:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A303816C05
1.958,1.531 2.365,1.531 false 1.958,1.281 2.365,1.281 false 2.781,1.271 3.188,1.271 false 1.781,1.448 2.094,1.604 0.313,0.156 10 false *a 1.823,1.198 2.135,1.354 0.313,0.156 10 false *b 3.24,1.208 3.427,1.365 0.188,0.156 10 false *b
*a Retainer
*b Claw
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

Connect the fuel lines and push in the retainer to engage the 2 claws. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




h.

Quick Type D:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A377479C01
1.406,4.323 1.583,4.323 1.583,4.323 1.583,3.948 false 1.938,4.458 1.938,4.333 false 2.25,3.573 2.375,3.302 2.375,3.302 2.521,3.302 false 1.885,3.427 1.885,3.104 1.885,3.104 2.031,3.104 false 2.333,1.698 2.531,1.698 false 2.573,0.719 2.573,0.979 false 2.458,0.719 3.104,0.719 3.104,0.719 3.104,0.99 false 1.854,4.469 2.167,4.625 0.313,0.156 10 false *a 2.563,3.219 2.875,3.375 0.313,0.156 10 false *b 2.083,3.021 2.396,3.177 0.313,0.156 10 false *c 1.24,4.25 1.552,4.406 0.313,0.156 10 false *d 2.292,0.635 2.604,0.792 0.313,0.156 10 false *e 2.167,1.615 2.479,1.771 0.313,0.156 10 false *a
*a Retainer
*b Fuel Pipe
*c Fuel Tube Connector
*d O-ring
*e Claw
V100135

Push
V100136

Pull out
V100137

Pull off


Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tube connector from the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe (fuel pipe).




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



i.

Quick Type D:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A299346C05
1,0.646 0.948,0.646 false 2.448,0.635 3.167,0.635 3.167,0.635 3.167,0.865 false 2.552,0.854 2.552,0.635 false 2.323,1.531 2.563,1.531 false 2.146,1.448 2.458,1.604 0.313,0.156 10 false *a 2.271,0.563 2.583,0.719 0.313,0.156 10 false *b
*a Retainer
*b Claw
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

Connect the fuel lines and push in the retainer to engage the 2 claws. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




j.

Quick Type E:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A374320C02
1.135,2.469 1.448,2.469 false 2.146,3.469 2.146,3.125 2.146,3.125 2.281,3.125 false 2.604,3.906 2.708,4.281 2.708,4.281 2.823,4.281 false 1.719,4.281 2.073,4.281 2.073,4.281 2.073,3.958 false 1.927,4.271 1.927,3.948 false 2.344,3.052 2.656,3.208 0.313,0.156 10 false *a 2.885,4.219 3.198,4.375 0.313,0.156 10 false *b 0.948,2.385 1.26,2.542 0.313,0.156 10 false *c 1.552,4.219 1.865,4.375 0.313,0.156 10 false *d
*a Fuel Tube Connector
*b Fuel Pipe
*c Retainer
*d O-ring
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the fuel tube connector.


ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).



iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



k.

Quick Type E:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A374321C02
1.115,2.74 1.469,2.74 false 0.948,2.667 1.26,2.823 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe and push them together. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

Connect the fuel lines and push in the retainer. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




l.
A224872C09
1.865,0.313 1.74,0.792 false 2.75,0.313 2.604,0.875 false 1.021,1.823 0.854,1.344 false 1.802,1.344 1.875,1.625 1.875,1.625 1.938,1.344 true 2.802,0.24 2.99,0.406 0.188,0.167 10 false *2 1.781,1.677 1.969,1.844 0.188,0.167 10 false *3 1.063,1.802 1.25,1.969 0.188,0.167 10 false *a 1.917,0.219 2.104,0.385 0.188,0.167 10 false *1
*1 Fuel Tank Breather Tube Connector
*2 Pipe
*3 O-ring
*a Nylon Tube


Quick Type F:

Observe these precautions when disconnecting the charcoal canister outlet tube connector:

i.

Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.


ii.
A224871C08
2.375,1.198 2.469,1.354 false 3.052,1.188 2.958,1.365 false 2.156,1.115 2.333,1.281 0.177,0.167 10 false *1 3.083,1.063 3.26,1.229 0.177,0.167 10 false *a
*1 Fuel Tank Breather Tube Connector
*a Pipe
V100135

Push
V100136

Pinch


Pinch the retainer and pull out the fuel tank breather tube connector with the fuel tank breather tube connector pushed to the pipe side to disconnect the fuel tank breather tube from the pipe.

NOTICE:

Do not use any tools.



iii.

If the connector and pipe are stuck, pinch the retainer with your hand, and then push and pull the connector to disconnect them.

NOTICE:

Do not use any tools.



iv.

Check the sealing surfaces of the disconnected parts, and clean them if necessary.


v.

Protect the contact surface by covering it with a plastic bag.

NOTICE:

Do not damage the pipe or fuel tube connector, and prevent entry of foreign objects.




m.
A224875C07
0,0 0,0 false
V100135

Push


Quick Type F:

Observe these precautions when connecting the charcoal canister outlet tube connector:

i.

Check that there are no scratches or foreign objects on the connecting part.


ii.

Align the fuel tank breather tube connector with the pipe, then push in the fuel tank breather tube connector until the retainer makes a "click" sound to install the fuel tank breather tube to the pipe.


iii.

After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.


iv.
A224876C07
0,0 0,0 false
V100135

Push


Inspect for fuel leak.

Click hereEngine / Hybrid System>2ZR-FXE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION



n.

Metallic Type:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A374324

Remove the No. 1 fuel pipe clamp.


ii.
A300491N03
0.479,1.427 0.479,1.198 0.479,1.198 0.792,1.052 false 2.469,1.25 2.615,0.906 2.615,0.906 2.792,0.906 false 2.854,0.844 3.177,1.042 0.323,0.198 10 false SST 0.365,1.469 0.823,1.667 0.458,0.198 10 false SST

Install SST (fuel hose puller) to the fuel tube connector as shown in the illustration.

SST
09268-21011  


iii.
A300492C07
2.188,1.396 2.49,1.698 2.49,1.698 2.688,1.698 false 0.396,0.281 0.802,0.281 0.802,0.281 0.802,0.427 true 0.531,0.604 0.531,0.281 false 1.26,1.24 1.26,0.729 1.26,0.729 1.073,0.729 true 0.896,0.958 1.26,0.958 false 0.229,0.198 0.479,0.385 0.25,0.188 10 false *a 2.74,1.646 3.135,1.844 0.396,0.198 10 false SST 1.177,1.24 1.49,1.396 0.313,0.156 10 false *a
*a Retainer (4 places)


Turn SST (fuel hose puller), align the retainers inside the fuel tube connector with the SST (fuel hose puller) chamfers and insert SST (fuel hose puller) into the fuel tube connector.


iv.

Mount the retainer of the fuel tube connector onto the chamfered part of SST (fuel hose puller).


v.
A076220C16
2.26,1.573 2.26,1.875 false 0.594,1.375 0.594,1.708 false 1.396,0.875 1.125,0.438 1.125,0.438 1.594,0.875 false 2.917,1.323 2.917,1.531 false 2.156,0.771 2.281,0.438 2.281,0.438 2.417,0.438 false 0.948,0.323 1.25,0.563 0.302,0.24 10 false *b 2.479,0.354 2.833,0.563 0.354,0.208 10 false *a 2.844,1.573 3.073,1.771 0.229,0.198 10 false *e 0.51,1.74 0.719,1.969 0.208,0.229 10 false *c 2.177,1.917 2.385,2.115 0.208,0.198 10 false *d
*a Retainer
*b O-ring
*c Nylon Tube
*d Fuel Tube Connector
*e Fuel Pipe


Slide SST (fuel hose puller) and the fuel tube connector together until they make a "click" sound, and then disconnect the fuel tube sub-assembly.

NOTICE:
·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




vi.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


vii.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



o.

Metallic Type:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A304571C01
1.813,1.229 1.969,1.427 0.156,0.198 10 false .
V100135

Pull


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Install a new No. 1 fuel pipe clamp.




p.
A289951C03
2.333,0.427 2.521,0.427 2.521,0.427 2.823,0.74 false 0.917,1.615 1.104,1.615 1.104,1.615 1.365,1.333 false 1.708,1.281 1.906,1.594 1.906,1.594 2.052,1.594 false 2.156,0.354 2.448,0.594 0.292,0.24 10 *a 2.115,1.531 2.438,1.792 0.323,0.26 10 *b 0.698,1.563 1,1.823 0.302,0.26 10 *c
*a Fuel Tube Connector
*b Nylon Tube
*c Ethylene Propylene Diene Monomer (EPDM) Rubber Protector


Observe the following precautions when handling a nylon tube:

NOTICE:
·

Do not twist the nylon tube of the fuel tube connector or fuel tube connector when connecting it.

·

Do not remove the Ethylene Propylene Diene Monomer (EPDM) rubber protector on the outside of the nylon tube.

·

Do not bend, twist, pinch or kink the nylon tube.





FUEL INJECTOR ASSEMBLY


a.
A222009C12
0.159,0.131 3.222,1.397 3.063,1.265 0.159,1.464 3.222,3.214 3.063,1.75 0.224,0.191 0.418,0.45 0.194,0.258 10 *a 0.212,1.523 0.406,1.782 0.194,0.258 10 *b 0.676,1.17 0.87,1.428 0.194,0.258 10 *1 1.138,1.17 1.332,1.428 0.194,0.258 10 *2 0.76,0.907 0.76,1.17 false 1.216,1.06 1.216,1.17 false 0.66,2.707 0.854,2.966 0.194,0.258 10 *1 1.122,2.707 1.316,2.966 0.194,0.258 10 *2 0.744,2.376 0.744,2.707 false 1.2,2.545 1.2,2.707 false
*1 O-ring
*2 Fuel Delivery Pipe Sub-assembly
*a Correct
*b Incorrect


Observe the following precautions when removing and installing the fuel injector assemblies:

i.

Do not reuse the O-ring.


ii.

When installing a new O-ring to the fuel injector assembly, do not damage the O-ring.


iii.

Apply gasoline or spindle oil to a new O-ring before installing it.

NOTICE:

Do not use engine oil, gear oil or brake fluid.




b.
A217166C14
2.396,0.292 2.083,0.146 2.083,0.146 1.542,0.146 false 2.5,0.667 2.854,0.938 2.854,0.938 3,0.938 true 1.115,1.531 0.625,1.031 0.625,1.031 0.458,1.031 false 1.469,1.177 0.979,0.677 0.979,0.677 0.813,0.677 true 1.375,0.073 1.573,0.365 0.198,0.292 10 false *1 3.052,0.854 3.281,1.135 0.229,0.281 10 false *2 0.281,0.958 0.521,1.208 0.24,0.25 10 false *4 0.646,0.594 0.885,0.844 0.24,0.25 10 false *3
*1 Fuel Delivery Pipe Sub-assembly
*2 O-ring
*3 Fuel Injector Assembly
*4 Injector Vibration Insulator


Install the fuel injector assembly to the cylinder head sub-assembly as shown in the illustration.

i.

Do not reuse the injector vibration insulator.




FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


NOTICE:
A398082C01
0.625,1.51 0.958,1.51 false 0.396,1.406 0.708,1.604 0.313,0.198 10 false *a
*a Tube


Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the plate sub-assembly.



INSPECT FOR FUEL LEAK


a.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs.

Click hereEngine / Hybrid System>2ZR-FXE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION