Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY) › from 2020.08
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404393 HV RELAY ASSEMBLY(for LITHIUM-ION BATTERY) A

2ZR-FXE HYBRID / BATTERY CONTROL  HV RELAY ASSEMBLY(for LITHIUM-ION BATTERY)  INSTALLATION  


PROCEDURE

Hide G92Z0 1.INSTALL HV BATTERY JUNCTION BLOCK ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Install the HV battery junction block assembly to the HV battery with the 4 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:

If the HV battery junction block assembly has been struck or dropped, replace it with a new one.



b.

Engage the 2 claws to install the wiring harness protector.


c.

Connect the 2 HV battery junction block assembly connectors.

NOTICE:

Make sure that the connectors are connected securely.



d.

Install the electric vehicle battery plug assembly to the HV battery with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


e.

Connect the hybrid battery terminal block connector.

NOTICE:

Make sure that the connector is connected securely.



f.

Connect the HV battery junction block assembly connector.

NOTICE:

Make sure that the connector is connected securely.



g.

Engage the 2 claws to close the wiring harness protector.


Hide G920L 2.INSTALL UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY

Hide 76974F 9.INSTALL REAR UNDER SIDE COVER LH

Hide 67918A 10.INSTALL REAR DOOR SCUFF PLATE LH

Hide 76973F 11.INSTALL REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 67917A 12.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 72693 13.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 14.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 17. PERFORM CURRENT SENSOR OFFSET LEARNING

HINT:

Perform this procedure when the HV battery junction block assembly or battery ECU assembly has been replaced.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Perform a road test.

NOTICE:

Accelerate and decelerate gently. Avoid rapid acceleration and deceleration.


i.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid Battery Current.

Powertrain > HV Battery > Data List
Tester Display
Hybrid Battery Current
50003 398 289

ii.

Drive the vehicle with the value of Data List item "Hybrid Battery Current" between -50 A and 50 A.

HINT:

Distance and driving time are not specified.



iii.

Turn the power switch off and leave the vehicle for 30 seconds or more.


iv.

Turn the power switch on (IG).


v.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid Battery Current.

Powertrain > HV Battery > Data List
Tester Display
Hybrid Battery Current
50003 398 289

vi.

Check that the value of "Hybrid Battery Current" is between -0.5 A and 0.5 A with the power switch on (IG).

NOTICE:

If the value is outside the specified range, perform the road test again.


HINT:
·

When the power switch is on (IG), if value of "Hybrid Battery Current" is between -0.5 A and 0.5 A, current sensor offset learning has been completed.

·

Even if the current sensor offset learning is not complete, the current sensor value will be corrected by repeating the road test a maximum of 7 times.