The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front door lock with motor assembly removal/installation are shown below.
After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal (for Audio and Visual System).
After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal (for Navigation System (for Radio and Display Type)).
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for 2ZR-FXE:
Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>REMOVAL
for M20A-FXS:
Click hereGeneral>MAINTENANCE>M20A-FXS AUXILIARY BATTERY>REMOVAL
69284C
3.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
74232
4.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)
74231
5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)
67602
6.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
68172A
7.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP
68195
8.REMOVE FRONT DOOR BELT SEAL
67832
9.REMOVE FRONT DOOR SERVICE HOLE COVER
68102
10.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
67664
11.REMOVE DOOR FRAME UPPER GARNISH
68151C
12.REMOVE FRONT DOOR GLASS RUN
67404F
13.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
69217D
14.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)
69040A
15.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY
| *1 | Front Door Lock Open Rod |
|
Remove in this Direction |
Disconnect the connector.
Using a T30 "TORX" socket wrench, remove the 3 screws.
Disconnect the front door lock open rod as shown in the illustration.
Remove the front door lock with motor assembly.
When reusing the front door lock with motor assembly (w/o Double Locking System):
Remove the door lock wiring harness seal from the front door lock with motor assembly.
When reusing the front door lock with motor assembly (w/ Double Locking System):
Remove the door lock wiring harness seal from the front door lock with motor assembly.
69035A
16.REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY (w/o Double Locking System)
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.
Disengage the guides to remove the front door lock cover sub-assembly from the front door lock with motor assembly.
69720B
17.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
w/o Double Locking System:
Disengage the guide to remove the front door lock remote control cable assembly from the front door lock with motor assembly.
w/ Double Locking System:
Disengage the guide to remove the front door lock remote control cable assembly from the front door lock with motor assembly.
69760C
18.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY
w/o Double Locking System:
Disengage the guide to remove the front door inside locking cable assembly from the front door lock with motor assembly.
w/ Double Locking System:
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.
Disengage the guide to remove the front door inside locking cable assembly from the front door lock with motor assembly.