52023
1.INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY
Install the rear bumper reinforcement sub-assembly with the 8 bolts.
52563A
2.INSTALL REAR BUMPER UPPER RETAINER LH
Install the rear bumper upper retainer LH with screw.
52562B
3.INSTALL REAR BUMPER UPPER RETAINER RH
Use the same procedure as for the LH side.
4.INSTALL REAR COMBINATION LIGHT LH
for LED Type:
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for LED Type)>INSTALLATION
for Bulb Type:
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Bulb Type)>INSTALLATION
5.INSTALL REAR COMBINATION LIGHT RH
Use the same procedure as for the LH side.
81498
6.INSTALL REAR COMBINATION LIGHT COVER LH
for LED Type:
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for LED Type)>INSTALLATION
for Bulb Type:
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Bulb Type)>INSTALLATION
81498
7.INSTALL REAR COMBINATION LIGHT COVER RH
Use the same procedure as for the LH side.
52576B
8.INSTALL REAR BUMPER SIDE RETAINER LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the claw and guide to install rear bumper side retainer LH as shown in the illustration.
Install the 2 screws.
52575
9.INSTALL REAR BUMPER SIDE RETAINER RH
Use the same procedure as for the LH side.
52453
10.INSTALL REAR BUMPER CENTER GUARD
Engage the claws and guides to install the rear bumper center guard.
Install the 2 clips and 6 outside moulding retainers.
| *a | Clip | *b | Outside Moulding Retainer |
52154B
11.INSTALL REAR BUMPER SIDE STAY LH
|
Install in this Direction |
Engage the claw to install the rear bumper side stay LH as shown in the illustration.
Install the clip and screw.
52153A
12.INSTALL REAR BUMPER SIDE STAY RH
Use the same procedure as for the LH side.
52463
13.INSTALL REAR BUMPER PAD LH
When installing the rear bumper pad LH, heat the rear bumper assembly using a heat light.
| Item | Temperature |
|---|---|
| Rear Bumper Assembly | 40 to 60°C (104 to 140°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear bumper assembly excessively.
Clean the rear bumper assembly surface.
Using a heat light, heat the rear bumper assembly surface.
Remove the double-sided tape from the rear bumper assembly.
Wipe off any tape adhesive residue with cleaner.
Remove the release paper from a new rear bumper pad LH.
After removing the release paper, keep the exposed adhesive free from foreign matter.
| *a | Scribed Line |
Install the rear bumper pad LH as shown in the illustration.
Install the rear bumper pad LH along the scribed line on the rear bumper cover.
52462
14.INSTALL REAR BUMPER PAD RH
Use the same procedure as for the LH side.
52461F
15.INSTALL REAR BUMPER PAD
When installing the rear bumper pad, heat the rear bumper assembly using a heat light.
| Item | Temperature |
|---|---|
| Rear Bumper Assembly | 40 to 60°C (104 to 140°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear bumper assembly excessively.
Clean the rear bumper assembly surface.
Using a heat light, heat the rear bumper assembly surface.
Remove the double-sided tape from the rear bumper assembly.
Wipe off any tape adhesive residue with cleaner.
Remove the release paper from a new rear bumper pad.
After removing the release paper, keep the exposed adhesive free from foreign matter.
| *a | Scribed Line |
Install the rear bumper pad as shown in the illustration.
Install the rear bumper pad along the scribed line on the rear bumper cover.
52162B
16.INSTALL NO. 1 REAR BUMPER PLATE
Engage the hook to install the No. 1 rear bumper plate.
Disengage the claws.
52753
17.INSTALL REAR BUMPER SIDE MOULDING LH (w/ Side Moulding)
|
Install in this Direction |
Engage the claws to install the rear bumper side moulding LH as shown in the illustration.
Install the 3 screws.
52752
18.INSTALL REAR BUMPER SIDE MOULDING RH (w/ Side Moulding)
Use the same procedure as for the LH side.
52164A
19.INSTALL REAR BUMPER PLATE LH
|
Install in this Direction |
Engage the claws to install the rear bumper plate LH as shown in the illustration.
Install the 2 screws.
52163A
20.INSTALL REAR BUMPER PLATE RH
Use the same procedure as for the LH side.
81920
21.INSTALL REFLEX REFLECTOR ASSEMBLY LH
|
Install in this Direction |
Engage the guide and claw to install the reflex reflector assembly LH as shown in the illustration.
Install the screw.
81910
22.INSTALL REFLEX REFLECTOR ASSEMBLY RH
Use the same procedure as for the LH side.
52166A
23.INSTALL REAR BUMPER UPPER COVER LH
Engage the hook to install the rear bumper upper cover LH.
52165A
24.INSTALL REAR BUMPER UPPER COVER RH
Use the same procedure as for the LH side.
82169A
25.INSTALL NO. 6 FLOOR WIRE (w/ Wire Harness)
w/ TOYOTA Parking Assist-sensor System and Rear Fog Light:
Engage the clamps to install the No. 6 floor wire.
w/ Rear Fog Light:
Engage the clamps to install the No. 6 floor wire.
w/ TOYOTA Parking Assist-sensor System:
Engage the clamps to install the No. 6 floor wire.
81481Q
26.INSTALL FOG LIGHT BRACKET (w/o LED Back-up Light and Rear Fog Light)
Install the fog light bracket with the 2 screws.
81480B
27.INSTALL REAR FOG LIGHT ASSEMBLY (w/ Rear Fog Light)
for Bulb Type:
Click hereVehicle Exterior>LIGHTING (EXT)>REAR FOG LIGHT ASSEMBLY>INSTALLATION
for LED Type:
Click hereVehicle Exterior>LIGHTING (EXT)>REAR FOG LIGHT ASSEMBLY>INSTALLATION
28.INSTALL BACK UP LIGHT ASSEMBLY (w/ LED Back-up Light)
w/o Rear Fog Light:
Click hereVehicle Exterior>LIGHTING (EXT)>BACK-UP LIGHT ASSEMBLY>INSTALLATION
w/ Rear Fog Light:
Click hereVehicle Exterior>LIGHTING (EXT)>BACK-UP LIGHT ASSEMBLY>INSTALLATION
89348S
29.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89348R
30.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89348T
31.INSTALL REAR SIDE ULTRASONIC SENSOR RETAINER (w/ Simple Intelligent Parking Assist System)
89342A
32.INSTALL REAR CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89342
33.INSTALL REAR CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89342B
34.INSTALL REAR SIDE ULTRASONIC SENSOR (w/ Simple Intelligent Parking Assist System)