Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2022.01
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  DCM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
DCM Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "DCM" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "DCM" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "DCM" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "DCM Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Telematics transceiver branch line or connector

·

Power source circuit of telematics transceiver

·

Telematics transceiver ground circuit

·

Telematics transceiver



WIRING DIAGRAM

for Radio and Display Type with Dual Knob Type


C366199E20
0.115,1.729 2.094,1.927 1.979,0.198 10 false No. 3 CAN Junction Connector 2.146,2.198 3.604,2.51 1.458,0.313 10 false from Auxiliary Battery 2.146,2.729 3.573,2.979 1.427,0.25 10 false from IG2-NO. 2 Relay 2.469,3.281 3.625,3.552 1.156,0.271 10 false from ACC Relay 4.281,2.385 5.344,2.604 1.063,0.219 10 false DCM/MAYDAY 4.313,2.906 5.375,3.125 1.063,0.219 10 false ECU-IG2 NO. 3 4.531,3.438 5.594,3.656 1.063,0.219 10 false ECU-ACC 5.792,0.604 6.333,0.802 0.542,0.198 10 false CANP 5.802,1.146 6.344,1.344 0.542,0.198 10 false CANN 5.792,2.198 6.333,2.396 0.542,0.198 10 false +B 5.802,2.729 6.344,2.927 0.542,0.198 10 false IG2 5.802,3.292 6.344,3.49 0.542,0.198 10 false ACC 5.802,3.823 6.042,4.042 0.24,0.219 10 false E 5.5,4.219 6.042,4.417 0.542,0.198 10 false F165 5.479,4.375 7.01,4.615 1.531,0.24 10 false Telematics Transceiver 5.542,0.51 5.813,0.698 0.271,0.188 10 false 15 5.531,1.063 5.802,1.25 0.271,0.188 10 false 16 5.573,2.115 5.844,2.302 0.271,0.188 10 false 1 5.583,2.646 5.854,2.833 0.271,0.188 10 false 7 5.573,3.188 5.844,3.375 0.271,0.188 10 false 8 5.583,3.74 5.854,3.927 0.271,0.188 10 false 4 0.115,1.563 0.656,1.76 0.542,0.198 10 false F114 1.625,1.063 1.896,1.25 0.271,0.188 10 false 19 1.635,0.51 1.906,0.698 0.271,0.188 10 false 8


for Radio and Display Type with Single Knob Type


C392585E11
0.146,1.594 0.76,1.792 0.615,0.198 10 false F114 0.135,1.771 2.281,2.063 2.146,0.292 10 false No. 3 CAN Junction Connector 2.198,2.323 3.698,2.594 1.5,0.271 10 false from Auxiliary Battery 2.208,3.313 3.594,3.552 1.385,0.24 10 false from IG2-NO. 2 Relay 4.354,3.521 5.385,3.74 1.031,0.219 10 false ECU-IG2 NO. 3 4.323,2.51 5.469,2.75 1.146,0.24 10 false DCM/MAYDAY 5.813,2.344 6.427,2.542 0.615,0.198 10 false +B 5.813,3.333 6.125,3.531 0.313,0.198 10 false IG2 5.802,4.25 6.417,4.448 0.615,0.198 10 false E 5.406,4.771 5.865,4.969 0.458,0.198 10 false F175 5.396,4.948 7.031,5.177 1.635,0.229 10 false Telematics Transceiver 5.813,0.615 6.427,0.813 0.615,0.198 10 false CANP 5.813,1.156 6.427,1.354 0.615,0.198 10 false CANN 5.573,2.24 5.729,2.438 0.156,0.198 10 false 1 5.51,3.24 5.823,3.438 0.313,0.198 10 false 19 5.521,4.146 5.76,4.344 0.24,0.198 10 false 20 5.521,0.51 5.833,0.708 0.313,0.198 10 false 25 5.531,1.063 5.844,1.26 0.313,0.198 10 false 26 1.656,0.521 1.813,0.719 0.156,0.198 10 false 8 1.635,1.052 1.948,1.25 0.313,0.198 10 false 19


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
Result:
Result Proceed to
for Radio and Display Type with Dual Knob Type A
for Radio and Display Type with Single Knob Type B



A

2.CHECK FOR OPEN IN CAN BUS LINES (TELEMATICS TRANSCEIVER BRANCH LINE)

B

4.CHECK FOR OPEN IN CAN BUS LINES (TELEMATICS TRANSCEIVER BRANCH LINE)
2.CHECK FOR OPEN IN CAN BUS LINES (TELEMATICS TRANSCEIVER BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the telematics transceiver connector.


c.
C285245C46
1.5,0.083 2,0.333 0.5,0.25 1.823,1.208 1.167,1.917 true 2.031,1.219 2.542,1.927 true 0.052,0.042 0.385,0.302 0.333,0.26 10 false *a 2.615,1.854 3.229,2.052 0.615,0.198 10 false CANN 0.719,1.823 1.333,2.021 0.615,0.198 10 false CANP 1.552,0.135 2.167,0.417 0.615,0.281 10 false F165
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F165-15 (CANP) - F165-16 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (TELEMATICS TRANSCEIVER)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C285245C47
1.5,0.083 2,0.333 0.5,0.25 0.74,0.26 0.427,0.885 true 2.375,0.896 2.792,0.25 true 0.396,1.208 0.25,1.865 true 0.594,1.208 0.885,1.865 true 0.052,0.042 0.385,0.302 0.333,0.26 10 false *a 2.865,0.146 3.104,0.344 0.24,0.198 10 false E 0.75,1.885 1.365,2.083 0.615,0.198 10 false ACC 1.573,0.135 2.354,0.375 0.781,0.24 10 false F165 0.781,0.177 1.396,0.375 0.615,0.198 10 false +B 0.135,1.906 0.75,2.104 0.615,0.198 10 false IG2
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F165-4 (E) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F165-1 (+B) - Body ground Power switch off 11 to 14 V
F165-7 (IG2) - Body ground Power switch on (IG) 11 to 14 V
F165-8 (ACC) - Body ground Power switch on (ACC) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK FOR OPEN IN CAN BUS LINES (TELEMATICS TRANSCEIVER BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the telematics transceiver connector.


c.
C427756C41
1.427,0.24 1.927,0.49 0.5,0.25 0.917,1.833 1.188,1.24 true 1.313,1.229 1.583,1.833 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.531,0.281 1.969,0.49 0.438,0.208 10 false F175 1.625,1.75 2.042,2 0.417,0.25 10 false CANN 0.5,1.75 0.917,2 0.417,0.25 10 false CANP
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F175-25 (CANP) - F175-26 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (TELEMATICS TRANSCEIVER)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C427756C42
1.427,0.24 1.927,0.49 0.5,0.25 0.646,1.906 0.406,1.219 true 0.521,1.229 0.854,1.76 true 0.333,1.021 0.698,0.521 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.531,0.281 1.969,0.49 0.438,0.208 10 false F175 0.875,1.76 1.292,2.01 0.417,0.25 10 false E 0.635,1.927 1.052,2.177 0.417,0.25 10 false IG2 0.74,0.417 1.156,0.667 0.417,0.25 10 false +B
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F175-20 (E) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F175-1 (+B) - Body ground Power switch off 11 to 14 V
F175-19 (IG2) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)