Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall with Dual Knob Type Radio and Display) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0524446 TELEMATICS SYSTEM(for eCall with Dual Knob Type Radio and Display) C

TELEMATICS  TELEMATICS SYSTEM(for eCall with Dual Knob Type Radio and Display)  B15C0  GPS Antenna Disconnected (Short)  B15C1  GPS Antenna Disconnected (Open)  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the No. 1 amplifier antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 GPS Antenna Disconnected (Short) Current to the No. 1 amplifier antenna assembly is lower than the malfunction threshold for 10 seconds or more when the power switch is on (IG)
(Short circuit)
·

Telematics transceiver

·

No. 1 amplifier antenna assembly

·

No. 4 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

Antenna divider


B15C1 GPS Antenna Disconnected (Open) Current to the No. 1 amplifier antenna assembly is higher than the malfunction threshold for 10 seconds or more when the power switch is on (IG)
(Open circuit)
·

Telematics transceiver

·

No. 1 amplifier antenna assembly

·

No. 4 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

Antenna divider



WIRING DIAGRAM

E359864E05
0.094,0.094 3.948,0.333 3.854,0.24 12 false w/ Navigation System: 0.094,2.167 1.281,2.656 1.188,0.49 10 false No. 1 Amplifier Antenna Assembly 4.323,1.948 4.875,2.375 0.552,0.427 10 false Antenna Divider 5.688,2.25 7.125,3.198 1.438,0.948 10 false Telematics Transceiver 5.604,1.292 5.917,1.49 0.313,0.198 10 false GA 5.615,1.719 5.927,1.917 0.313,0.198 10 false GA 5,1.292 5.313,1.49 0.313,0.198 10 false AD 5,1.729 5.313,1.927 0.313,0.198 10 false AD 3.99,1.281 4.302,1.479 0.313,0.198 10 false AD 3.99,1.719 4.302,1.917 0.313,0.198 10 false AD 3.375,1.281 3.531,1.479 0.156,0.198 10 false A 3.385,1.719 3.542,1.917 0.156,0.198 10 false A 3,1.271 3.156,1.469 0.156,0.198 10 false B 3,1.719 3.156,1.917 0.156,0.198 10 false B 2.281,1.281 2.438,1.479 0.156,0.198 10 false C 2.281,1.729 2.438,1.927 0.156,0.198 10 false C 1.906,1.271 2.063,1.469 0.156,0.198 10 false D 1.906,1.729 2.063,1.927 0.156,0.198 10 false D 1.219,1.26 1.531,1.458 0.313,0.198 10 false RA 1.219,1.729 1.531,1.927 0.313,0.198 10 false RA 5.333,2.156 5.646,2.354 0.313,0.198 10 false *1 3.688,2.156 4,2.354 0.313,0.198 10 false *1 2.635,2.156 2.948,2.354 0.313,0.198 10 false *2 1.563,2.156 1.875,2.354 0.313,0.198 10 false *3 1.271,1.073 1.427,1.271 0.156,0.198 10 false 5 1.229,1.521 1.542,1.719 0.313,0.198 10 false 5a 1.906,1.073 2.063,1.271 0.156,0.198 10 false 2 2.292,1.073 2.448,1.271 0.156,0.198 10 false 2 3,1.073 3.156,1.271 0.156,0.198 10 false 2 3.385,1.073 3.542,1.271 0.156,0.198 10 false 2 1.865,1.531 2.177,1.729 0.313,0.198 10 false 2a 2.24,1.531 2.552,1.729 0.313,0.198 10 false 2a 2.979,1.531 3.292,1.729 0.313,0.198 10 false 2a 3.344,1.531 3.656,1.729 0.313,0.198 10 false 2a 4.031,1.094 4.188,1.292 0.156,0.198 10 false 6 4,1.531 4.313,1.729 0.313,0.198 10 false 6a 5.042,1.073 5.198,1.271 0.156,0.198 10 false 5 5.01,1.521 5.323,1.719 0.313,0.198 10 false 5a 5.635,1.094 5.792,1.292 0.156,0.198 10 false 1 5.615,1.51 5.927,1.708 0.313,0.198 10 false 1a 1.417,2.698 5.854,2.896 4.438,0.198 10 false *1: Antenna Cord Sub-assembly 1.417,3.021 5.854,3.219 4.438,0.198 10 false *2: No. 2 Antenna Cord Sub-assembly 1.427,3.365 5.865,3.563 4.438,0.198 10 false *3: No. 3 Antenna Cord Sub-assembly

E359865E07
0.115,0.115 4.156,0.354 4.042,0.24 12 false w/o Navigation System: 0.115,2.281 1.302,2.719 1.188,0.438 10 false No. 1 Amplifier Antenna Assembly 5.635,2.385 7.125,3.219 1.49,0.833 10 false Telematics Transceiver 5.469,1.417 5.781,1.615 0.313,0.198 10 false GA 5.469,1.844 5.781,2.042 0.313,0.198 10 false GA 4.438,1.406 4.594,1.604 0.156,0.198 10 false A 4.438,1.844 4.594,2.042 0.156,0.198 10 false A 4.063,1.396 4.219,1.594 0.156,0.198 10 false B 4.063,1.854 4.219,2.052 0.156,0.198 10 false B 2.729,1.406 2.885,1.604 0.156,0.198 10 false C 2.729,1.854 2.885,2.052 0.156,0.198 10 false C 2.365,1.396 2.521,1.594 0.156,0.198 10 false D 2.365,1.854 2.521,2.052 0.156,0.198 10 false D 1.219,1.396 1.531,1.594 0.313,0.198 10 false RA 1.219,1.844 1.531,2.042 0.313,0.198 10 false RA 1.26,1.208 1.417,1.406 0.156,0.198 10 false 5 1.24,1.656 1.552,1.854 0.313,0.198 10 false 5a 2.365,1.208 2.521,1.406 0.156,0.198 10 false 2 2.729,1.208 2.885,1.406 0.156,0.198 10 false 2 4.052,1.208 4.208,1.406 0.156,0.198 10 false 2 4.458,1.208 4.615,1.406 0.156,0.198 10 false 2 5.531,1.219 5.688,1.417 0.156,0.198 10 false 1 2.333,1.656 2.646,1.854 0.313,0.198 10 false 2a 2.698,1.656 3.01,1.854 0.313,0.198 10 false 2a 4.021,1.656 4.333,1.854 0.313,0.198 10 false 2a 4.406,1.656 4.719,1.854 0.313,0.198 10 false 2a 5.479,1.656 5.792,1.854 0.313,0.198 10 false 1a 4.979,2.292 5.292,2.49 0.313,0.198 10 false *1 3.396,2.292 3.708,2.49 0.313,0.198 10 false *2 1.792,2.292 2.104,2.49 0.313,0.198 10 false *3 1.438,2.698 5.875,2.896 4.438,0.198 10 false *1: Antenna Cord Sub-assembly 1.438,3.042 5.875,3.24 4.438,0.198 10 false *2: No. 2 Antenna Cord Sub-assembly 1.438,3.365 5.875,3.563 4.438,0.198 10 false *3: No. 3 Antenna Cord Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Dual Knob Type Radio and Display)>REGISTRATION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG) and wait for 10 seconds.


d.

Turn the GTS on.


e.

f.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Dual Knob Type Radio and Display)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
2.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E389828C07
1.479,0.302 1.917,0.521 0.438,0.219 1.469,2.729 1.906,2.948 0.438,0.219 1.844,1.344 2.26,0.927 true 1.708,4.135 2.125,3.656 true 2.313,0.792 2.771,1.167 0.458,0.375 10 false 5a 1.563,4.135 1.875,4.333 0.313,0.198 10 false 2a 1.594,0.344 1.906,0.542 0.313,0.198 10 false RA 1.635,2.771 1.948,2.969 0.313,0.198 10 false D 0.333,0.281 0.646,0.479 0.313,0.198 10 false *a 0.323,2.625 0.635,2.823 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Disconnect the No. 3 antenna cord sub-assembly from the No. 1 amplifier antenna assembly connector.


b.

Disconnect the No. 3 antenna cord sub-assembly from the No. 2 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-5 - D-2 Always Below 1 Ω
RA-5a - D-2a Always Below 1 Ω
RA-5 or D-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ANTENNA CORD SUB-ASSEMBLY NO.2

NG

REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY

3.INSPECT ANTENNA CORD SUB-ASSEMBLY NO.2
a.
E383188C06
1.469,2.365 1.875,2.604 0.406,0.24 1.469,0.427 1.875,0.667 0.406,0.24 1.313,1.448 1.573,1.906 true 1.281,3.365 1.542,3.823 true 1.625,0.469 2,0.708 0.375,0.24 10 false C 1.615,2.406 1.99,2.646 0.375,0.24 10 false B 1.563,1.938 1.938,2.177 0.375,0.24 10 false 2a 0.24,0.292 0.552,0.448 0.313,0.156 10 false *a 0.198,2.333 0.51,2.49 0.313,0.156 10 false *b 1.552,3.854 1.927,4.094 0.375,0.24 10 false 2a
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the No. 2 antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.


b.

Disconnect the No. 2 antenna cord sub-assembly from the antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - C-2 Always Below 1 Ω
B-2a - C-2a Always Below 1 Ω
B-2 or C-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK VEHICLE TYPE

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

4.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Navigation System A
w/o Navigation System B



A

5.INSPECT ANTENNA CORD SUB-ASSEMBLY

B

7.INSPECT ANTENNA CORD SUB-ASSEMBLY
5.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E429285C02
1.552,1.635 1.958,1.875 0.406,0.24 1.531,0.146 1.938,0.385 0.406,0.24 1.542,2.979 1.948,3.219 0.406,0.24 1.969,4.031 2.24,3.698 2.24,3.698 2.365,3.698 true 2.469,2.271 2.719,1.885 2.719,1.885 2.844,1.885 true 2.135,2.448 2.354,2.906 2.354,2.906 2.479,2.906 true 2.438,0.969 2.604,1.323 2.604,1.323 2.729,1.323 true 1.677,0.198 2.052,0.438 0.375,0.24 10 false A 1.625,2.406 2,2.646 0.375,0.24 10 false E 2.906,1.823 3.281,2.063 0.375,0.24 10 false 6a 2.438,3.615 2.813,3.854 0.375,0.24 10 false 1a 1.656,1.688 2.031,1.927 0.375,0.24 10 false AD 1.635,3.021 2.01,3.26 0.375,0.24 10 false GA 2.552,2.844 2.927,3.083 0.375,0.24 10 false 5a 2.792,1.26 3.167,1.5 0.375,0.24 10 false 1a 0.302,0.167 0.677,0.406 0.375,0.24 10 false *a 0.302,1.792 0.677,2.031 0.375,0.24 10 false *b 0.365,3.135 0.74,3.375 0.375,0.24 10 false *c
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Divider)
*c Front view of wire harness connector
(to Telematics Transceiver)


Disconnect the antenna cord sub-assembly from the No. 2 antenna cord sub-assembly connector.


b.

Disconnect the antenna cord sub-assembly from the antenna divider connector.


c.

Disconnect the antenna cord sub-assembly from the telematics transceiver connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - AD-1 Always Below 1 Ω
A-2a - AD-1a Always Below 1 Ω
AD-2 - GA-1 Always Below 1 Ω
AD-2a - GA-1a Always Below 1 Ω
A-2 or AD-1 - Body ground Always 10 kΩ or higher
AD-2 or GA-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT ANTENNA DIVIDER

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

6.INSPECT ANTENNA DIVIDER
a.
E241596C26
2.021,1.417 1.938,1.823 true 2.302,1.417 2.552,1.823 true 1.865,1.854 2.292,2.031 0.427,0.177 10 false 2a 2.51,1.865 2.938,2.042 0.427,0.177 10 false 1a 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Remove the antenna divider.

Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always Below 1 Ω
1a - 2a Always Below 1 Ω
1 - 1a Always 10 kΩ or higher
2 - 2a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

7.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E405966C03
1.573,2.323 2.01,2.583 0.438,0.26 1.583,0.417 2.021,0.677 0.438,0.26 2.51,1.99 2.229,1.49 true 2.417,3.229 1.99,3.531 true 1.74,0.49 1.896,0.688 0.156,0.198 10 false A 1.688,2.385 1.969,2.646 0.281,0.26 10 false GA 2.531,2.021 2.802,2.271 0.271,0.25 10 false 2a 2.469,3.083 2.74,3.333 0.271,0.25 10 false 1a 0.354,0.229 0.667,0.385 0.313,0.156 10 false *a 0.427,2.302 0.74,2.458 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telematics Transceiver)


Disconnect the antenna cord sub-assembly from the No. 2 antenna cord sub-assembly connector.


b.

Disconnect the antenna cord sub-assembly from the telematics transceiver.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - GA-1 Always Below 1 Ω
A-2a - GA-1a Always Below 1 Ω
A-2 or GA-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

8.REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.

c.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Dual Knob Type Radio and Display)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG

9.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
9.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT