Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0524469 TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display) C

TELEMATICS  TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display)  B15CB11  Telephone Main Antenna Circuit Short to Ground  B15CB13  Telephone Main Antenna Circuit Open  


DESCRIPTION

If an open or short circuit in the roof antenna assembly is detected as a result of a terminal check performed by the telephone transceiver assembly, these DTCs will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15CB11 Telephone Main Antenna Circuit Short to Ground Roof antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Short circuit)
·

Telephone transceiver assembly

·

No. 2 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Roof antenna assembly


B15CB13 Telephone Main Antenna Circuit Open Roof antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Open circuit)
·

Telephone transceiver assembly

·

No. 2 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Roof antenna assembly



WIRING DIAGRAM

E359861E09
5.646,2.188 7.042,2.563 1.396,0.375 10 false Telephone Transceiver Assembly 0.083,2.073 1.667,2.5 1.583,0.427 10 false Roof Antenna Assembly 4.469,2.125 4.781,2.323 0.313,0.198 10 false *1 2.146,2.125 2.458,2.323 0.313,0.198 10 false *2 5.542,1.229 5.854,1.427 0.313,0.198 10 false C 5.531,1.667 5.844,1.865 0.313,0.198 10 false C 1.292,1.208 1.604,1.406 0.313,0.198 10 false I 1.302,1.667 1.615,1.865 0.313,0.198 10 false I 3.438,1.219 3.594,1.417 0.156,0.198 10 false G 3.438,1.677 3.594,1.875 0.156,0.198 10 false G 3.073,1.219 3.229,1.417 0.156,0.198 10 false H 3.073,1.677 3.229,1.875 0.156,0.198 10 false H 5.531,1.021 5.688,1.219 0.156,0.198 10 false 1 3.448,1.031 3.604,1.229 0.156,0.198 10 false 1 3.083,1.031 3.24,1.229 0.156,0.198 10 false 1 5.5,1.469 5.813,1.667 0.313,0.198 10 false 1a 3.406,1.469 3.719,1.667 0.313,0.198 10 false 1a 3.042,1.458 3.354,1.656 0.313,0.198 10 false 1a 1.26,1.021 1.417,1.219 0.156,0.198 10 false 4 1.229,1.469 1.542,1.667 0.313,0.198 10 false 4a 5.844,1.208 6.302,1.406 0.458,0.198 10 false TEL 1.323,2.823 5.76,3.021 4.438,0.198 10 false *1: No. 2 Antenna Cord Sub-assembly 1.323,3.156 5.76,3.354 4.438,0.198 10 false *2: No. 3 Antenna Cord Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.

·

Before replacing the telephone transceiver assembly, refer to Service Bulletin.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Telematics > Trouble Codes
50001 459

Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



A

B

2.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
2.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E397959C12
1.438,0.427 1.938,0.677 0.5,0.25 1.969,0.99 2.198,0.813 true 0.375,0.229 0.688,0.427 0.313,0.198 10 false *a 2.25,0.698 2.563,0.896 0.313,0.198 10 false 2a 1.635,0.448 1.792,0.646 0.156,0.198 10 false G
*a Component without harness connected
(No. 2 Antenna Cord Sub-assembly)


Disconnect the No. 2 antenna cord sub-assembly connector from the No. 3 antenna cord sub-assembly.


b.
E419263C01
1.49,0.229 1.906,0.49 0.417,0.26 1.896,1.406 2.26,1.75 true 0.271,0.208 0.583,0.406 0.313,0.198 10 false *a 2.302,1.74 2.615,1.938 0.313,0.198 10 false 1a 1.646,0.271 1.802,0.469 0.156,0.198 10 false C
*a Component without harness connected
(No. 2 Antenna Cord Sub-assembly)


Disconnect the No. 2 antenna cord sub-assembly connector from the Telephone Transceiver Assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G-2 - C-1 Always Below 1 Ω
G-2a - C-1a Always Below 1 Ω
G-2 or C-1 - Body ground Always 10 kΩ or higher
G-2a or C-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

3.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E487726C01
2.313,0.99 2.729,1.24 0.417,0.25 1.854,1.073 2.292,0.719 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 2.49,1.042 2.802,1.24 0.313,0.198 10 false I 2.354,0.594 2.667,0.792 0.313,0.198 10 false 5a
*a Component without harness connected
(No. 3 Antenna Cord Sub-assembly)


Disconnect the No. 3 antenna cord sub-assembly connector from the roof antenna assembly.


b.
E393322C09
1.5,0.167 2,0.417 0.5,0.25 1.479,1.021 1.031,0.667 true 0.146,0.083 0.458,0.281 0.313,0.198 10 false *a 0.854,0.5 1.167,0.698 0.313,0.198 10 false 2a 1.708,0.219 2.021,0.417 0.313,0.198 10 false H
*a Component without harness connected
(No. 3 Antenna Cord Sub-assembly)


Disconnect the No. 3 antenna cord sub-assembly connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I-5 - H-2 Always Below 1 Ω
I-5a - H-2a Always Below 1 Ω
I-5 or H-2 - Body ground Always 10 kΩ or higher
I-5a or H-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ROOF ANTENNA ASSEMBLY

NG

4.REPLACE ROOF ANTENNA ASSEMBLY
a.

Replace the roof antenna assembly with a known good one and check if the same problem occurs again.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL

OK:

The system returns to normal.



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT