These DTCs are stored when a malfunction occurs in the roof antenna assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C111 | GNSS Antenna Circuit Short to Ground | Current to the telephone antenna assembly is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Short circuit) |
·
Telephone transceiver assembly ·
No. 2 antenna cord sub-assembly ·
No. 3 antenna cord sub-assembly ·
Roof antenna assembly |
| B15C113 | GNSS Antenna Circuit Open | Current to the telephone antenna assembly is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Open circuit) |
·
Telephone transceiver assembly ·
No. 2 antenna cord sub-assembly ·
No. 3 antenna cord sub-assembly ·
Roof antenna assembly |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Before replacing the telephone transceiver assembly, refer to Service Bulletin.
Turn the ignition switch to ON and wait for 10 seconds or more.
Turn the GTS on.
Clear the DTCs.
Check for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Component without harness connected
(No. 2 Antenna Cord Sub-assembly) |
Disconnect the No. 2 antenna cord sub-assembly connector from the No. 3 antenna cord sub-assembly.
| *a | Component without harness connected
(No. 2 Antenna Cord Sub-assembly) |
Disconnect the No. 2 antenna cord sub-assembly connector from the Telephone Transceiver Assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G-2 - B-1 | Always | Below 1 Ω |
| G-2a - B-1a | Always | Below 1 Ω |
| G-2 or B-1 - Body ground | Always | 10 kΩ or higher |
| G-2a or B-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(No. 3 Antenna Cord Sub-assembly) |
Disconnect the No. 3 antenna cord sub-assembly connector from the roof antenna assembly.
| *a | Component without harness connected
(No. 3 Antenna Cord Sub-assembly) |
Disconnect the No. 3 antenna cord sub-assembly connector from the No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I-5 - B-2 | Always | Below 1 Ω |
| I-5a - B-2a | Always | Below 1 Ω |
| I-5 or B-2 - Body ground | Always | 10 kΩ or higher |
| I-5a or B-2a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the roof antenna assembly with a known good one and check if the same problem occurs again.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL
The system returns to normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT