Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0524469 TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display) C

TELEMATICS  TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display)  B153711  Telephone Sub Antenna Circuit Short to Ground  B153713  Telephone Sub Antenna Circuit Open  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B153711 Telephone Sub Antenna Circuit Short to Ground Navigation antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Short circuit)
·

Telephone transceiver assembly

·

Navigation antenna assembly

·

Antenna cord sub-assembly

·

No. 4 antenna cord sub-assembly


B153713 Telephone Sub Antenna Circuit Open Navigation antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Open circuit)
·

Telephone transceiver assembly

·

Navigation antenna assembly

·

Antenna cord sub-assembly

·

No. 4 antenna cord sub-assembly



WIRING DIAGRAM

E359861E07
0.083,2.073 1.302,2.469 1.219,0.396 10 false Navigation Antenna Assembly 1.271,1.198 1.594,1.406 0.323,0.208 10 false D 5.521,1.208 5.844,1.417 0.323,0.208 10 false A 5.646,2.177 7.042,2.573 1.396,0.396 10 false Telephone Transceiver Assembly 1.271,1.021 1.521,1.229 0.25,0.208 10 false 4 5.51,1 5.76,1.208 0.25,0.208 10 false 1 1.271,1.667 1.594,1.875 0.323,0.208 10 false D 1.24,1.469 1.49,1.677 0.25,0.208 10 false 4a 3.063,1.01 3.313,1.219 0.25,0.208 10 false 2 3.469,1.021 3.719,1.229 0.25,0.208 10 false 2 3.042,1.458 3.292,1.667 0.25,0.208 10 false 2a 3.417,1.458 3.667,1.667 0.25,0.208 10 false 2a 3.063,1.208 3.313,1.417 0.25,0.208 10 false F 3.094,1.667 3.344,1.875 0.25,0.208 10 false F 3.448,1.667 3.698,1.875 0.25,0.208 10 false E 3.448,1.208 3.698,1.417 0.25,0.208 10 false E 5.542,1.667 5.865,1.875 0.323,0.208 10 false A 5.49,1.458 5.74,1.667 0.25,0.208 10 false 1a 4.49,2.073 4.74,2.281 0.25,0.208 10 false *1 2.167,2.073 2.417,2.281 0.25,0.208 10 false *2 0.698,2.906 3.74,3.167 3.042,0.26 10 false *1: No. 4 Antenna Cord Sub-assembly 0.698,3.323 2.906,3.615 2.208,0.292 10 false *2: Antenna Cord Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.

·

Before replacing the telephone transceiver assembly, refer to Service Bulletin.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

c.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NAVIGATION ANTENNA ASSEMBLY
2.INSPECT NAVIGATION ANTENNA ASSEMBLY
a.

Remove the navigation antenna assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.
E356744C02
1.375,1.188 1.417,0.844 false 1.438,0.802 1.302,0.323 false 0.135,0.146 0.448,0.344 0.313,0.198 10 false *a 1.198,1.156 1.406,1.385 0.208,0.229 10 false 4a 1.188,0.156 1.396,0.385 0.208,0.229 10 false 4
*a Component without harness connected
(Navigation Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4a Always 4 to 11 kΩ



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NAVIGATION ANTENNA ASSEMBLY

3.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY
a.
E334514C68
0.656,1.031 1.031,1.281 0.375,0.25 2.167,0.865 2.375,0.438 true 0.792,1.073 1.104,1.271 0.313,0.198 10 false D 2.417,0.333 2.729,0.531 0.313,0.198 10 false 4a 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Component without harness connected
(No. 4 Antenna Cord Sub-assembly)


E397959C10
1.458,0.333 1.875,0.583 0.417,0.25 1.969,1.021 2.302,0.667 true 1.625,0.375 1.781,0.573 0.156,0.198 10 false F 2.354,0.573 2.688,0.771 0.333,0.198 10 false 2a 0.167,0.146 0.365,0.323 0.198,0.177 10 false *a
*a Component without harness connected
(Antenna Cord Sub-assembly)


Disconnect the No. 4 antenna cord sub-assembly from the navigation antenna assembly.


b.

Disconnect the No. 4 antenna cord sub-assembly from the antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F-2 - D-4 Always Below 1 Ω
F-2a - D-4a Always Below 1 Ω
F-2 or D-4 - Body ground Always 10 kΩ or higher
F-2a or D-4a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 4 ANTENNA CORD SUB-ASSEMBLY

4.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E393322C10
1.5,0.167 2,0.417 0.5,0.25 1.479,1.021 1.031,0.667 true 0.146,0.083 0.458,0.281 0.313,0.198 10 false *a 0.854,0.5 1.167,0.698 0.313,0.198 10 false 2a 1.708,0.219 2.021,0.417 0.313,0.198 10 false E
*a Component without harness connected
(Antenna Cord Sub-assembly)


Disconnect the antenna cord sub-assembly connector from the telephone and navigation antenna assembly.


b.
E418543C07
1.448,0.167 1.865,0.417 0.417,0.25 1.854,1.323 2.448,0.813 true 1.615,0.229 1.771,0.427 0.156,0.198 10 false A 2.51,0.719 2.844,0.917 0.333,0.198 10 false 1a 0.167,0.146 0.365,0.323 0.198,0.177 10 false *a
*a Component without harness connected
(Antenna Cord Sub-assembly)


Disconnect the antenna cord sub-assembly connector from the Telephone Transceiver Assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-2 - A-1 Always Below 1 Ω
E-2a - A-1a Always Below 1 Ω
E-2 or A-1 - Body ground Always 10 kΩ or higher
E-2a or A-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT