Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P023511  Turbocharger/Supercharger Boost Sensor "A" Circuit Short to Ground  


DESCRIPTION

A327839E02
0.073,0.052 0.844,0.25 0.771,0.198 10 false Voltage (V) 0.958,0.26 3,0.573 2.042,0.313 10 false Intercooler internal pressure 0.24,0.74 1.01,0.938 0.771,0.198 10 false 4.5 0.25,1.563 1.021,1.76 0.771,0.198 10 false 2.0 0.25,2.01 1.021,2.208 0.771,0.198 10 false 1.0 3.021,2.375 3.396,2.802 0.375,0.427 10 false kPa 3,2.854 3.427,3.24 0.427,0.385 10 false psi 0.854,2.563 1.302,2.771 0.448,0.208 10 false 13.30 1.458,2.563 1.906,2.771 0.448,0.208 10 false 96.15 2.51,2.563 3.083,2.781 0.573,0.219 10 false 303.30 0.917,3.042 1.271,3.271 0.354,0.229 10 false 1.93 1.49,3.052 2.031,3.323 0.542,0.271 10 false 13.94 2.552,3.052 3.031,3.281 0.479,0.229 10 false 43.98

The internal sensor in the No. 1 turbo pressure sensor detects the intercooler internal pressure as a voltage.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P023511 Turbocharger/Supercharger Boost Sensor "A" Circuit Short to Ground The No. 1 turbo pressure sensor output voltage is less than 0.97 V for 3 seconds or more (1 trip detection logic).
·

Open or short in No. 1 turbo pressure sensor circuit

·

No. 1 turbo pressure sensor

·

ECM


Comes on DTC stored SAE Code: P0237

HINT:

When this DTC is output, check the No. 1 turbo pressure sensor in the Data List. Enter the following menus: Powertrain / Engine / Data List / All Data / Boost Pressure Sensor.

DTC No. Boost Pressure Sensor Malfunction
P023511 Approximately 11 kPa [2 psi] or less
·

Short to ground in PTA circuit

·

Short in PTA to EPTA circuit

·

Open in VPTA circuit



If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM monitors the No. 1 turbo pressure sensor voltage and uses this value to calculate the intercooler internal pressure. When the No. 1 turbo pressure sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the No. 1 turbo pressure sensor circuit and stores this DTC.

Example:

If the No. 1 turbo pressure sensor output voltage is less than 0.97 V for 3 seconds or more, the ECM store this DTC

MONITOR STRATEGY

Required Sensors/Components No. 1 turbo pressure sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P023511.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A330721E91
5.25,3.26 5.781,3.49 0.531,0.229 10 false ECM 0.292,3.052 2.375,3.521 2.083,0.469 10 false No. 1 Turbo Pressure Sensor 0.292,2.885 0.656,3.083 0.365,0.198 10 false C3 5.25,3.094 5.615,3.292 0.365,0.198 10 false C62 1.406,1.031 1.771,1.229 0.365,0.198 10 false VC 1.344,1.729 1.708,1.927 0.365,0.198 10 false PIM 1.438,2.51 1.802,2.708 0.365,0.198 10 false E2 1.74,0.917 2.104,1.115 0.365,0.198 10 false 3 1.75,2.375 2.115,2.573 0.365,0.198 10 false 2 1.74,1.615 2.104,1.813 0.365,0.198 10 false 1 4.281,0.917 4.542,1.094 0.26,0.177 10 false 140 4.281,1.594 4.542,1.771 0.26,0.177 10 false 108 4.271,2.365 4.531,2.542 0.26,0.177 10 false 139 4.615,0.906 5.167,1.167 0.552,0.26 10 false VPTA 4.625,1.604 4.99,1.802 0.365,0.198 10 false PTA 4.635,2.365 5.25,2.615 0.615,0.25 10 false EPTA 5.615,0.688 5.979,0.885 0.365,0.198 10 false 5 V

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 TURBO PRESSURE SENSOR)
A347474C31
0.25,1.948 0.688,2.219 0.438,0.271 1.083,2.792 1.271,2.281 true 1.615,2.813 1.594,2.302 true 2.156,2.813 1.906,2.302 true 0.188,0.177 0.646,0.375 0.458,0.198 10 false *a 0.375,2.01 0.833,2.208 0.458,0.198 10 false C3 0.948,2.844 1.406,3.042 0.458,0.198 10 false PIM 1.542,2.844 2,3.042 0.458,0.198 10 false E2 2.104,2.844 2.563,3.042 0.458,0.198 10 false VC
*a Front view of wire harness connector
(to No. 1 Turbo Pressure Sensor)


a.

Disconnect the No. 1 turbo pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C3-3 (VC) - C3-2 (E2) Ignition switch ON 4.75 to 5.25 V
C3-1 (PIM) - C3-2 (E2) Ignition switch ON 3.0 to 5.25 V



Result:
Proceed to
OK
NG



OK

2.REPLACE NO. 1 TURBO PRESSURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)
2.REPLACE NO. 1 TURBO PRESSURE SENSOR

Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS (P023511)
3.CHECK WHETHER DTC OUTPUT RECURS (P023511)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTC.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

j.

Read the DTCs.


Result:
Result Proceed to
DTCs are not output A
DTC P023511 is output B



A

B

4.CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the C3 No. 1 turbo pressure sensor connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C3-3 (VC) - C62-140 (VPTA) Always Below 1 Ω
C3-1 (PIM) or C62-108 (PTA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR