The turbocharger and intercooler cooling system is a water cooling system that is independent from the engine cooling system. It uses a dedicated radiator and electric water pump assembly to cool the intercooler and turbocharger. The electric water pump assembly uses duty cycle signals sent from the ECM to provide stepless, optimal control of the electric water pump assembly speed.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P023A12 | Charge Air Cooler Coolant Pump Control Circuit Short to Battery | Electric water pump assembly output voltage is specified value or higher (1 trip detection logic). | ·
Open or short in electric water pump assembly circuit ·
Electric water pump assembly ·
ECM |
Does not come on | DTC stored | SAE Code: P023C |
| P023A13 | Charge Air Cooler Coolant Pump Control Circuit Open | Electric water pump assembly speed is less than 10 rpm (1 trip detection logic). | ·
Open or short in electric water pump assembly circuit ·
Electric water pump assembly ·
EFI-MAIN NO. 2 relay ·
ECM |
Does not come on | DTC stored | SAE Code: P023A |
| P023A14 | Charge Air Cooler Coolant Pump Control Circuit Short to Ground or Open | Electric water pump assembly output voltage is specified value or less (1 trip detection logic). | ·
Open or short in electric water pump assembly circuit ·
Electric water pump assembly ·
EFI-MAIN NO. 2 relay ·
ECM |
Does not come on | DTC stored | SAE Code: P023B |
If the electric water pump assembly operates at less than 10 rpm, the ECM determines there is a malfunction and stores DTC P023A13.
The electric water pump assembly operates steplessly according to duty cycle signals from the ECM. The ECM monitors the current operation speed of the electric water pump assembly. When the actual drive duty cycle ratio deviates from the target drive duty cycle, the ECM determines there is a malfunction and stores DTC P023A12 or P023A14.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P023A12, P023A13 or P023A14.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again.
Inspect the fuses for circuits related to this system before performing the following procedure.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Intercooler Water Pump.
| Tester Display |
|---|
| Control the Intercooler Water Pump |
According to the display on the GTS, perform the Active Test and check that the electric water pump assembly operates.
The electric water pump assembly is operating (vibrating).
Use a sound scope if the operation is difficult to check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A56 electric water pump assembly connector.
Disconnect the A38 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A56-2 (NWP) - A38-11 (IWPI) | Always | Below 1 Ω |
| A56-3 (SWP) - A38-24 (IWPO) | Always | Below 1 Ω |
| A56-2 (NWP) or A38-11 (IWPI) - Body ground and other terminals | Always | 10 kΩ or higher |
| A56-3 (SWP) or A38-24 (IWPO) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Electric Water Pump Assembly) |
Disconnect the electric water pump assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A56-2 (NWP) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Electric Water Pump Assembly) |
Disconnect the electric water pump assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A56-4 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A56 electric water pump assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A56-1 (PGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A56 electric water pump assembly connector.
Disconnect the A38 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A56-2 (NWP) - A38-11 (IWPI) | Always | Below 1 Ω |
| A56-3 (SWP) - A38-24 (IWPO) | Always | Below 1 Ω |
| A56-2 (NWP) or A38-11 (IWPI) - Body ground and other terminals | Always | 10 kΩ or higher |
| A56-3 (SWP) or A38-24 (IWPO) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the electric water pump assembly.
Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>WATER PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and warm it up.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P023A12, P023A13 or P023A14.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P023A12, P023A13 or P023A14 is output) |
B |
A
B
Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.
Disconnect the A56 electric water pump assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (EFI-MAIN NO. 2 relay holder) - A56-4 (+B) | Always | Below 1 Ω |
| 3 (EFI-MAIN NO. 2 relay holder) or A56-4 (+B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the EFI-MAIN NO. 2 relay.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No.1 Engine Room Relay Block |
| *2 | EFI-MAIN NO. 2 Relay Holder |
Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (EFI-MAIN NO. 2 relay holder) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block |
| *2 | EFI-MAIN NO. 2 Relay Holder |
Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (EFI-MAIN NO. 2 relay holder) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.
Disconnect the 1B No. 1 integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1B-4 - 1 (EFI-MAIN NO. 2 relay holder) | Always | Below 1 Ω |
| 1B-4 or 1 (EFI-MAIN NO. 2 relay holder) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG