When the ignition switch is turned to ON, battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the EFI-MAIN relay, closing the contact of the EFI-MAIN relay and supplying power to terminals +B and +B2 of the ECM.
Inspect the fuses for circuits related to this system before performing the following procedure.
Disconnect the 1A and 1B No. 1 integration relay connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1A-10 - Body ground | Always | 11 to 14 V |
| 1B-3 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 1 integration relay (EFI-MAIN relay, IG2 NO. 1 relay).
Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 1A and 1B No. 1 integration relay connector.
Disconnect the A38 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1A-9 - A38-6 (IGSW) | Always | Below 1 Ω |
| 1B-6 - A38-46 (MREL) | Always | Below 1 Ω |
| 1B-4 - A38-2 (+B) | Always | Below 1 Ω |
| 1B-4 - A38-3 (+B2) | Always | Below 1 Ω |
| 1A-9 or A38-6 (IGSW) - Body ground and other terminals | Always | 10 kΩ or higher |
| 1B-6 or A38-46 (MREL) - Body ground and other terminals | Always | 10 kΩ or higher |
| 1B-4 or A38-2 (+B) - Body ground and other terminals | Always | 10 kΩ or higher |
| 1B-4 or A38-3 (+B2) - Body ground and other terminals | Always | 10 kΩ or higher |
If a short is detected in any of the above circuits, there may be a malfunction in the circuit of a connected ECU.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 1A and 1B No. 1 integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1A-8 - Body ground | Always | Below 1 Ω |
| 1B-5 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C62-53 (E1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A38-6 (IGSW) - Body ground | Ignition switch ON | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Entry and Start System) | B |
| NG (w/o Entry and Start System) | C |
A
B
C
Disconnect the F1 certification ECU (smart key ECU assembly) connector.
Disconnect the 1A No. 1 integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-17 (IG1D) - 1A-7 | Always | Below 1 Ω |
| F1-17 (IG1D) or 1A-7 - Body ground and other terminals | Always | 10 kΩ or higher |
If a short is detected in any of the above circuits, there may be a malfunction in the circuit of a connected ECU.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F12 ignition or starter switch assembly connector.
Disconnect the 1A No. 1 integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F12-8 (IG1) - 1A-7 | Always | Below 1 Ω |
| F12-8 (IG1) or 1A-7 - Body ground and other terminals | Always | 10 kΩ or higher |
If a short is detected in any of the above circuits, there may be a malfunction in the circuit of a connected ECU.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition or starter switch assembly.
Click hereEngine / Hybrid System>8NR-FTS (STARTING)>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG