Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P019515  Engine Oil Temperature Sensor Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P019511.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P019511

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P019515 Engine Oil Temperature Sensor Circuit Short to Battery or Open The engine oil temperature sensor output voltage is higher than 4.93 V for 5 seconds or more (1 trip detection logic).
·

Open or short in engine oil temperature sensor circuit

·

Engine oil temperature sensor

·

ECM


Does not come on DTC stored SAE Code:
P0198

HINT:

When this DTC is output, check the engine oil temperature in the Data List. Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Oil Temperature Sensor.

DTC No. Engine Oil Temperature Sensor Malfunction
P019515 -40°C (-40°F)
·

Short to +B in THEO circuit

·

Open in THEO circuit

·

Open in ETHE circuit



If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM monitors the engine oil temperature sensor and uses the sensor voltage to calculate the engine oil temperature. If the engine oil temperature sensor output voltage deviates from the normal operating range, the ECM determines that the engine oil temperature sensor circuit is malfunctioning and stores this DTC.

Example:

If the engine oil temperature sensor output voltage is higher than 4.93 V for 5 seconds or more, the ECM store this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and wait for the time indicated below.

-

If the engine oil temperature sensor is higher than -10°C (14°F): 15 seconds or more.

-

If the engine oil temperature sensor is -10°C (14°F) or less: 13 minutes or more.


9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P019515.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the engine oil temperature sensor connector.

A347472C15
3.917,1.396 4.354,1.635 0.438,0.24 2.208,1.219 2.823,1.417 0.615,0.198 10 false THEO 2.208,1.542 2.823,1.74 0.615,0.198 10 false ETHE 4.021,1.438 4.448,1.646 0.427,0.208 10 false C38 4.521,0.375 4.948,0.583 0.427,0.208 10 false *a 1.323,1.948 1.75,2.156 0.427,0.208 10 false *1 2.771,1.948 3.198,2.156 0.427,0.208 10 false *2
*1 Engine Oil Temperature Sensor *2 ECM
*a Front view of wire harness connector
(to Engine Oil Temperature Sensor)
- -



b.

Connect terminals 1 and 2 of the engine oil temperature sensor connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Oil Temperature Sensor.

Powertrain > Engine > Data List
Tester Display
Engine Oil Temperature Sensor
50003 372 261

g.

Read the value displayed on the GTS.

Standard Value:

164°C (327°F) or higher



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL TEMPERATURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (ENGINE OIL TEMPERATURE SENSOR - ECM)
a.

Disconnect the C38 engine oil temperature sensor connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C38-2 - C62-97 (THEO) Always Below 1 Ω
C38-1 - C62-96 (ETHE) Always Below 1 Ω
C38-2 or C62-97 (THEO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR