Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2018.05
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P21951D  A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Circuit Current Out of Range  P219523  A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Signal Stuck Low  P21961D  A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Circuit Current Out of Range  P219624  A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Signal Stuck High  


DESCRIPTION

The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection duration. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is a planar type and integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A363544E01
1.583,2.698 0.813,2.135 true 1.771,2.615 1.979,2.521 true 2.896,1.854 3.396,0.5 true 3.052,1.885 3.406,1.271 true 3.177,2.24 3.49,1.823 true 3.042,2.604 3.417,2.979 true 2.99,2.521 3.615,2.281 true 2.813,2.5 3.625,2.271 true 0.271,2.052 1.344,2.25 1.073,0.198 10 false Element 0.094,2.99 1.167,3.188 1.073,0.198 10 false Exhaust Gas 1.083,3.146 1.344,3.344 0.26,0.198 10 false A 1.958,3.135 2.219,3.333 0.26,0.198 10 false A 2.021,2.427 2.573,2.729 0.552,0.302 10 false Cover 3.448,0.396 4.573,1.156 1.125,0.76 10 false Solid Electrolyte (Zirconia Element) 3.469,1.188 4.229,1.615 0.76,0.427 10 false Alumina 3.542,1.74 4.302,2.167 0.76,0.427 10 false Heater 3.688,2.188 4.302,2.625 0.615,0.438 10 false Platinum Electrode 3.469,2.906 4.75,3.365 1.281,0.458 10 false Atmospheric Air 2.479,3.208 3.76,3.667 1.281,0.458 10 false A-A Cross Section 5.417,3.073 6.698,3.531 1.281,0.458 10 false Air Fuel Ratio 4.958,0.5 6.792,0.948 1.833,0.448 10 false ECM Monitored Air Fuel Ratio Sensor Voltage

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P21951D A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Circuit Current Out of Range While the fuel cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds or more (2 trip detection logic).
·

Air fuel ratio sensor

·

ECM


Comes on (Euro-OBD)/- (Except Euro-OBD) DTC stored (Euro-OBD)/- (Except Euro-OBD) SAE Code:
P2195
P219523 A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Signal Stuck Low Both of the following conditions are met for 5 seconds or more (2 trip detection logic):
(a) Air fuel ratio sensor voltage is higher than 3.8 V.
(b) Heated oxygen sensor voltage is 0.21 V or higher.
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure (for low pressure side)

·

Fuel pump (for low pressure side)

·

Fuel pressure (for high pressure side)

·

Fuel injector assembly

·

Fuel system

·

ECM


Comes on (Euro-OBD)/- (Except Euro-OBD) DTC stored (Euro-OBD)/- (Except Euro-OBD) SAE Code:
P2195
P21961D A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Circuit Current Out of Range While the fuel cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.47 mA for 3 seconds or more (2 trip detection logic).
·

Air fuel ratio sensor

·

ECM


Comes on (Euro-OBD)/- (Except Euro-OBD) DTC stored (Euro-OBD)/- (Except Euro-OBD) SAE Code:
P2196
P219624 A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Signal Stuck High Both of the following conditions are met for 5 seconds or more (2 trip detection logic):
(a) Air fuel ratio sensor voltage is less than 2.8 V.
(b) Heated oxygen sensor voltage is less than 0.71 V.
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure (for low pressure side)

·

Fuel pressure (for high pressure side)

·

Fuel injector assembly

·

Fuel system

·

ECM


Comes on (Euro-OBD)/- (Except Euro-OBD) DTC stored (Euro-OBD)/- (Except Euro-OBD) SAE Code:
P2196

HINT:
·

When any of these DTCs are stored, check the air fuel ratio sensor voltage output by entering the following menus on the GTS: Powertrain / Engine / Data List / All Data / A/F (O2) Sensor Voltage B1S1.

·

Short-term fuel trim values can also be read using the GTS.

·

The ECM regulates the voltages at the A1A+ and A1A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor voltage output cannot be confirmed without using the GTS.

·

If an air fuel ratio sensor malfunction is detected, the ECM will store a DTC.



MONITOR DESCRIPTION

Sensor Voltage Detection Monitor

Under air fuel ratio feedback control, If the air fuel ratio sensor output voltage is less than 2.8 V (very rich condition) for 5 seconds despite the heated oxygen sensor output voltage being less than 0.71 V, the ECM stores DTC P219624. Alternatively, if the air fuel ratio sensor output voltage is higher than 3.8 V (very lean condition) for 5 seconds despite the heated oxygen sensor output voltage being 0.21 V or higher, DTC P219523 is stored.


Sensor Current Detection Monitor

A rich air fuel mixture causes a low air fuel ratio sensor current, and a lean air fuel mixture causes a high air fuel ratio sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor current during fuel cut and detects any abnormal current values.

If the air fuel ratio sensor output is 2.2 mA or higher for 3 seconds or more of cumulative time, the ECM interprets this as a malfunction in the air fuel ratio sensor and stores DTC P21951D (stuck on high side). If the air fuel ratio sensor output is less than 0.47 mA for 3 seconds or more of cumulative time, the ECM stores DTC P21961D (stuck on low side).


A283591E10
2.313,2.292 2.417,1.667 2.417,1.667 2.583,1.667 false 5.771,2.292 5.917,1.667 5.917,1.667 6.083,1.667 false 4.375,2.292 4.5,1.667 4.5,1.667 4.667,1.667 false 0.094,0.115 2.5,0.333 2.406,0.219 10 false Air Fuel Ratio Sensor Current Monitor 2.917,0.417 6.083,0.667 3.167,0.25 10 false Cumulative Time "t" = t1 + t2 = 3 seconds or more 0.646,1.063 1.25,1.333 0.604,0.271 10 false Fuel cut 0.406,2.198 1.75,2.417 1.344,0.219 10 false Sensor Current (mA) 0.438,2.833 1.75,3.083 1.313,0.25 10 false High Side Threshold 0.479,3.49 1.75,3.75 1.271,0.26 10 false Low Side Threshold 1.469,0.938 1.75,1.167 0.281,0.229 10 false ON 1.417,1.25 1.75,1.5 0.333,0.25 10 false OFF 2.646,1.583 3.25,2 0.604,0.417 10 false Delay (3 seconds) 4.75,1.573 5.323,2 0.573,0.427 10 false Delay (3 seconds) 6.177,1.573 6.76,2 0.583,0.427 10 false Delay (3 seconds) 2.417,3.646 3.667,3.917 1.25,0.271 10 false 3 seconds or more 2.385,4.292 3.833,4.5 1.448,0.208 10 false Normal Sensor Output 4.677,4.281 6.25,4.5 1.573,0.219 10 false Abnormal Sensor Output 4.688,3.865 4.938,4.115 0.25,0.25 10 false t1 6.406,4.281 6.833,4.5 0.427,0.219 10 false Time 6.021,3.865 6.271,4.115 0.25,0.25 10 false t2

MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor
Required Sensors/Components (Related) Heated oxygen sensor
Frequency of Operation Continuous: Sensor voltage detection monitor
Once per driving cycle: Sensor current detection monitor
Duration 3 seconds: Sensor current detection monitor
5 seconds: Sensor voltage detection monitor

TYPICAL ENABLING CONDITIONS

Sensor Voltage Detection Monitor
Time after engine start 30 seconds or more
Fuel system status Closed loop

Sensor Current Detection Monitor
Battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [11.02 psi(abs)] or higher
Air fuel ratio sensor status Activated
Continuous time of fuel cut 3 seconds to 10 seconds

TYPICAL MALFUNCTION THRESHOLDS

P219523: Sensor Voltage Detection Monitor (Lean Side Malfunction)
Heated oxygen sensor voltage 0.21 V or higher
Air fuel ratio sensor voltage Higher than 3.8 V

P219624: Sensor Voltage Detection Monitor (Rich Side Malfunction)
Heated oxygen sensor voltage Less than 0.71 V
Air fuel ratio sensor voltage Less than 2.8 V

P21951D: Sensor Current Detection Monitor (High Side Malfunction)
Air fuel ratio sensor current 2.2 mA or higher

P21961D: Sensor Current Detection Monitor (Low Side Malfunction)
Air fuel ratio sensor current Less than 0.47 mA

CONFIRMATION DRIVING PATTERN

A283818E41
5.448,1.667 5.854,1.156 true 5.021,1.521 4.5,1.521 true 6.333,2.25 5.375,2.25 false 4.052,3.531 3.823,3.354 true 4.927,1.677 4.5,0.448 true 5.25,3.167 5.417,3.167 5.417,3.167 5.531,2.74 true 4.708,2.958 4.875,2.958 4.875,2.958 4.99,2.729 true 2.448,1.51 2.344,0.792 true 0.073,0.021 3.948,0.323 3.875,0.302 10 false Engine Coolant Temperature: 75°C (167°F) or higher 0.146,0.917 1.094,1.146 0.948,0.229 10 false Vehicle Speed 1.458,0.448 3.083,0.875 1.625,0.427 10 false Between 75 and 100 km/h (46 and 62 mph) 0.719,2.281 1.167,2.583 0.448,0.302 10 false Idling 1.25,2.865 2.083,3.083 0.833,0.219 10 false Warming up 2.49,2.875 3.219,3.396 0.729,0.521 10 false 10 minutes or more 3.396,1.469 4.51,1.865 1.115,0.396 10 false 75 km/h (46 mph) or more 3.396,0.292 4.5,0.708 1.104,0.417 10 false Accelerator Pedal Depressed 4.667,0.708 5.667,0.917 1,0.208 10 false At least 3 times 5.896,0.927 7.125,1.448 1.229,0.521 10 false Accelerator Pedal Released (Fuel cut) 6.448,2.135 7.01,2.5 0.563,0.365 10 false 10 km/h (6 mph) 6.25,2.552 6.667,2.802 0.417,0.25 10 false Time 4.115,3.083 5.344,3.354 1.229,0.271 10 false 4 seconds or more 4.094,3.469 5.417,3.667 1.323,0.198 10 false Refer to figure below 3.49,2.865 4.771,3.229 1.281,0.365 10 false 10 seconds or more 1.552,2.167 1.813,2.385 0.26,0.219 10 false [A] 2.708,1.302 2.969,1.521 0.26,0.219 10 false [B] 3.844,2.167 4.083,2.417 0.24,0.25 10 false [C] 4.99,1.302 5.25,1.521 0.26,0.219 10 false [D] 5.5,1.594 5.76,1.813 0.26,0.219 10 false [E] 6.083,3.115 6.344,3.333 0.26,0.219 10 false [F]

A268862E38
3.646,2.625 3.958,0.885 true 3.385,2.625 2.75,0.833 2.75,0.833 2.583,0.833 true 0.104,0.042 3.042,0.24 2.938,0.198 10 false Driving Pattern Detail for [C] through [E]: 0.188,0.458 1.958,0.656 1.771,0.198 10 false Reference Engine Speed 2.823,0.156 7,0.406 4.177,0.25 10 false Cumulative Detection Period "t" = t1 + t2 + t3 = 3 seconds or more 1.094,2.365 1.51,2.563 0.417,0.198 10 false Idling 2.188,2.948 2.698,3.229 0.51,0.281 10 false Idling 3.177,3.115 3.833,3.479 0.656,0.365 10 false 4 seconds or more 2.188,2.25 2.448,2.521 0.26,0.271 10 false [C] 3.031,1.146 3.313,1.469 0.281,0.323 10 false [D] 3.469,1.542 3.729,1.813 0.26,0.271 10 false [E] 1.469,0.729 2.656,0.927 1.188,0.198 10 false Delay (3 seconds) 3.979,0.74 5.417,0.938 1.438,0.198 10 false Detection Period t1 4.813,2.375 4.99,2.625 0.177,0.25 10 false t2 6.042,2.396 6.302,2.635 0.26,0.24 10 false t3 6.49,2.781 6.875,2.979 0.385,0.198 10 false Time 4.375,3.115 5.031,3.479 0.656,0.365 10 false 4 seconds or more 5.604,3.115 6.26,3.479 0.656,0.365 10 false 4 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

9.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for at least 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

With shift state M selected (for CVT) or second gear (for Manual Transaxle) [C], accelerate the vehicle to 75 km/h (47 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel cut control [E].

12.

Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).

13.

Repeat steps [C] through [E] above at least 3 times in one driving cycle.

14.

Enter the following menus: Powertrain / Engine / Trouble Codes [F].

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

17.

Input the DTC: P21951D, P219523, P21961D or P219624.

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P21951D, P219523, P21961D OR P219624)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

Result:
Result Proceed to
DTC P21951D, P219523, P21961D or P219624 is output A
DTC P21951D, P219523, P21961D or P219624 and P013613, P013617 or P01361C are output
DTC P21951D, P219523, P21961D or P219624 and other DTCs are output B


HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.




A

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?


Result:
Proceed to
YES
NO



YES

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D OR P219624)

NO

4.READ VALUE USING GTS (A/F (O2) SENSOR CURRENT B1S1)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D OR P219624)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

k.

Input the DTC: P21951D, P219523, P21961D or P219624.


l.

Check the DTC judgment.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P21951D, P219523, P21961D or P219624 is output)
B




A

DTC CAUSED BY RUNNING OUT OF FUEL

B

4.READ VALUE USING GTS (A/F (O2) SENSOR CURRENT B1S1)
4.READ VALUE USING GTS (A/F (O2) SENSOR CURRENT B1S1)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Enter the following menus: Powertrain / Engine / Data List / All Data / A/F (O2) Sensor Current B1S1.

Powertrain > Engine > Data List
Tester Display
A/F (O2) Sensor Current B1S1
50003 372 230

f.

Check the test value of the air fuel ratio sensor output current during fuel cut, referring to the Driving Pattern Detail for [C] through [E] in the Confirmation Driving Pattern.

HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the GTS.



Result:
Test Value Proceed to
Within normal range
(0.47 mA or higher, and less than 2.2 mA)
A
Outside normal range
(less than 0.47 mA, or 2.2 mA or higher)
B




A

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

16.REPLACE AIR FUEL RATIO SENSOR
5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
A/F (O2) Sensor Voltage B1S1
O2 Sensor Voltage B1S2
50004 372 8 225,218

f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


g.

Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard
GTS Display (Sensor) Injection Volume Status Voltage
A/F (O2) Sensor Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2 Sensor Voltage B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

Result:
Status of A/F (O2) Sensor Voltage B1S1 Status of O2 Sensor Voltage B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean Lean Actual air fuel ratio lean A
Rich Rich Actual air fuel ratio rich
Lean Lean/Rich Air fuel ratio sensor malfunction B
Rich Lean/Rich Air fuel ratio sensor malfunction
Lean/Rich Lean/Rich Normal


Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (A/F (O2) Sensor Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2 Sensor Voltage B1S2) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F Sensor, the A/F (O2) Sensor Voltage B1S1 is consistently below 3.1 V, and the O2 Sensor Voltage B1S2 is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor, the output voltage of the air fuel ratio sensor or heated oxygen sensor alternates correctly.

HINT:

Refer to "Data List / Active Test" [A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2].

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST





A

6.CHECK INTAKE SYSTEM

B

16.REPLACE AIR FUEL RATIO SENSOR
6.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in the intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

7.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE INTAKE SYSTEM

7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

8.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)
a.

Check the fuel pressure (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (FUEL PRESSURE (HIGH))

NG

15.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)
9.READ VALUE USING GTS (FUEL PRESSURE (HIGH))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine and warm it up.


e.

Enter the following menus: Powertrain / Engine / Data List / All Data / Fuel Pressure (High).

Powertrain > Engine > Data List
Tester Display
Fuel Pressure (High)
50003 372 265

f.

Read the values.

Standard:
GTS Display Condition Specified Condition
Fuel Pressure (High) Shift lever position: P or N (neutral)
A/C: Off
Engine idling
4000 to 18000 kPag
Shift lever position: P or N (neutral)
A/C: Off
Engine speed: 3000 rpm
8000 to 18000 kPag



Result:
Proceed to
OK
NG



OK

10.INSPECT FUEL INJECTOR ASSEMBLY

NG

REPAIR OR REPLACE FUEL SYSTEM (FOR HIGH PRESSURE SIDE)

10.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

11.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

11.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D OR P219624)
12.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D OR P219624)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

k.

Input the DTC: P21951D, P219523, P21961D or P219624.


l.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P21951D, P219523, P21961D or P219624 is output)
B




A

END

B

13.REPLACE ECM
13.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

k.

Input the DTC: P21951D, P219523, P21961D or P219624.


l.

Check the DTC judgment result.

Result
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit




Result:
Proceed to
NEXT



NEXT

END

15.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)
a.

Inspect the fuel pump (for low pressure side).

for 2WD: Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for 2WD)>INSPECTION

for AWD: Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for AWD)>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Result Proceed to
OK A
NG (for 2WD) B
NG (for AWD) C



A

REPAIR OR REPLACE FUEL LINE (FOR LOW PRESSURE SIDE)

B

REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)

C

REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)

16.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D OR P219624)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D OR P219624)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

k.

Input the DTC: P21951D, P219523, P21961D or P219624.


l.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P21951D, P219523, P21961D or P219624 is output)
B




A

END

B