Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P003312  Turbocharger / Supercharger Bypass Valve "A" Control Circuit Short to Battery  


DESCRIPTION

The air by-pass valve is installed to the turbocharger sub-assembly. It opens and closes in response to drive commands from the ECM. If the air by-pass valve closes during normal boosting and the throttle valve closes while boost pressure is being applied, the air by-pass valve will open and the excess pressure between the turbocharger and the throttle valve will be released.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P003312 Turbocharger / Supercharger Bypass Valve "A" Control Circuit Short to Battery Short to +B in air by-pass valve circuit (1 trip detection logic).
·

Short in air by-pass valve circuit

·

Turbocharger sub-assembly (air by-pass valve)

·

ECM


Does not come on DTC stored SAE Code: P0035

MONITOR DESCRIPTION

The ECM monitors the output voltage while the air by-pass valve is operating.

The air by-pass valve turns on and off according to switching of a transistor inside the ECM.

If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the air by-pass valve circuit and stores this DTC.

CONFIRMATION DRIVING PATTERN

A330723E18
4.448,0.958 4.802,0.667 4.802,0.667 5.021,0.667 false 3.042,1.854 2.635,1.344 2.635,1.344 2.438,1.344 false 0.25,0.292 1.354,0.542 1.104,0.25 10 false Vehicle Speed 0.198,0.677 1.375,0.938 1.177,0.26 10 false 50 km/h (31 mph) 0.927,2.042 1.542,2.24 0.615,0.198 10 false Idling 0.396,2.365 1.313,2.75 0.917,0.385 10 false Ignition switch ON 5.625,3.375 5.99,3.625 0.365,0.25 10 false [D] 1.427,1.26 2.729,1.563 1.302,0.302 10 false Fully depressed 5.083,0.604 6.031,0.792 0.948,0.188 10 false Released 2.198,1.885 2.656,2.083 0.458,0.198 10 false [A] 3.125,1.417 3.604,1.615 0.479,0.198 10 false [B] 4.906,1.406 5.365,1.604 0.458,0.198 10 false [C]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

9.

Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Quickly release the accelerator pedal from the fully depressed position [C].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P003312.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [D] again.




WIRING DIAGRAM

A384821E07
0.667,2.99 1.74,3.188 1.073,0.198 10 false Battery 4.188,1.646 5.458,1.885 1.271,0.24 10 false Air By-pass Valve 5.875,0.896 6.292,1.135 0.417,0.24 10 false ABV 5.875,2.677 6.406,2.896 0.531,0.219 10 false MREL 6.156,4.01 6.688,4.229 0.531,0.219 10 false ECM 5.531,0.823 5.948,1.063 0.417,0.24 10 false 67 5.49,1.042 5.906,1.281 0.417,0.24 10 false C62 5.521,2.563 5.938,2.802 0.417,0.24 10 false 46 5.49,2.792 5.906,3.031 0.417,0.24 10 false A38 4.76,0.938 5.177,1.177 0.417,0.24 10 false ABV 5.125,0.958 5.292,1.125 0.167,0.167 10 false 2 4.26,0.948 4.552,1.156 0.292,0.208 10 false +B 4.073,0.958 4.24,1.125 0.167,0.167 10 false 1 4.188,1.49 4.604,1.729 0.417,0.24 10 false C53 3.354,1.188 4.188,1.354 0.833,0.167 10 false EFI NO. 3 0.75,1.198 1.802,1.469 1.052,0.271 10 false EFI-MAIN NO. 1 2.198,2.125 2.927,2.354 0.729,0.229 10 false EFI-MAIN 1.948,1.698 2.104,1.896 0.156,0.198 10 false 6 2.969,1.708 3.125,1.906 0.156,0.198 10 false 5 1.938,0.958 2.094,1.156 0.156,0.198 10 false 3 2.969,0.958 3.125,1.156 0.156,0.198 10 false 4 0.51,2.031 1.542,2.229 1.031,0.198 10 false BATT MAIN 2.042,2.656 2.771,2.885 0.729,0.229 10 false 1B 2.063,2.844 3.615,3.208 1.552,0.365 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR BYPASS VALVE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Air Bypass Valve / Data List / All Data / Air Bypass Valve Control.

Powertrain > Engine > Active Test
Active Test Display
Activate the Air Bypass Valve
Data List Display
Air Bypass Valve Control
50004 372 12 282

e.

According to the display on the GTS, perform the Active Test and check the operation and operation sound of the air by-pass valve.

OK:
Active Test Standard
ON
·

ON is displayed for Data List item "Air Bypass Valve Control"

·

Air by-pass valve operates (operation sound is normal)





Result:
Proceed to
OK
NG



OK

NG

2.INSPECT AIR BY-PASS VALVE
2.INSPECT AIR BY-PASS VALVE

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE - ECM)

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY (AIR BY-PASS VALVE MALFUNCTION)

3.CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE - ECM)
a.

Disconnect the C53 air by-pass valve connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C53-2 (ABV) or C62-67 (ABV) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P003312)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P003312)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

k.

Input the DTC: P003312.


l.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P003312 is output)
B




A

B