Home › Engine / Hybrid System › 8NR-FTS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059498 8NR-FTS ENGINE MECHANICAL _0291516 REAR CRANKSHAFT OIL SEAL A

8NR-FTS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear engine oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision syatem
Initialize back door lock Power door lock control system (Click here)
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)*2 Stop and start system (Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF thermal Degradation Estimate" is not estimated correctly for K313
(Click here)
for K313F
(Click here)
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

VSC disabled or malfunctions

·

DTCs are stored

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)


PROCEDURE

Hide 31250 2.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)

·

for w/o Stop And Start System:

Click hereDrivetrain>CLUTCH>CLUTCH UNIT (for EC6A)>REMOVAL

·

for w/ Stop And Start System:

Click hereDrivetrain>CLUTCH>CLUTCH UNIT (for EC69)>REMOVAL


Hide 32101B 3.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

a.
A351484N01
1.958,1.646 2.135,0.333 2.135,0.333 0.438,0.427 true 1.635,1.656 2.125,0.333 false 2.219,0.271 2.677,0.469 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-70011  (09213-70020)
09330-00021  


b.
A351485

Remove the 8 bolts, the rear drive plate spacer, the drive plate and ring gear sub-assembly and the front drive plate spacer.


Hide 13405 4.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

a.
A351484N01
1.958,1.646 2.135,0.333 2.135,0.333 0.438,0.427 true 1.635,1.656 2.125,0.333 false 2.219,0.271 2.677,0.469 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-70011  (09213-70020)
09330-00021  


b.
A357245

Remove the 8 bolts and flywheel sub-assembly.


Hide 11401L 5.REMOVE REAR ENGINE OIL SEAL

a.
A351486C02
0.406,0.417 0.656,1.094 true 2.729,0.927 1.813,1.313 true 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 2.792,0.823 3.104,1.021 0.313,0.198 10 false *b
*a Cut Position
*b Protective Tape


Using a knife, cut off the lip of the rear engine oil seal.


b.

Using a screwdriver with its tip wrapped with protective tape, pry out the rear engine oil seal.

NOTICE:

Be careful not to damage the crankshaft.