The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the continuously variable transaxle assembly removal/installation are shown below.
*1: When performing learning using the GTS.
| *a | Heavy object exceeding the capacity of the transmission jack |
Because the continuously variable transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.
If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.
When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.
Touching high-temperature areas such as the engine and exhaust pipe could result in burns.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>REMOVAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
3.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
4.REMOVE FRONT WHEELS
51441
5.REMOVE NO. 1 ENGINE UNDER COVER
51443C
6.REMOVE REAR ENGINE UNDER COVER RH
51444A
7.REMOVE REAR ENGINE UNDER COVER LH
58166
8.REMOVE FRONT FLOOR COVER LH (w/ Cover)
58165B
9.REMOVE FRONT FLOOR COVER RH (w/ Cover)
10.DRAIN ENGINE COOLANT
11.DRAIN COOLANT (for Intercooler)
12.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID
13.REMOVE WINDSHIELD WIPER MOTOR AND LINK
55737B
14.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
55735A
15.REMOVE WATER GUARD PLATE LH
55736D
16.REMOVE COWL BODY MOUNTING REINFORCEMENT LH
55735C
17.REMOVE COWL BODY MOUNTING REINFORCEMENT RH
55701J
18.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
19.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
28800
20.REMOVE BATTERY
53141F
21.REMOVE RADIATOR COVER
17751
22.REMOVE NO. 1 AIR CLEANER INLET
23.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
17701
24.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
89661
25.REMOVE ECM
74404A
26.REMOVE BATTERY CLAMP SUB-ASSEMBLY
Remove the bolt and nut to separate the engine wire from the battery clamp sub-assembly.
Disengage the clamp to separate the engine wire from the battery clamp sub-assembly.
Remove the 3 bolts and battery clamp sub-assembly from the vehicle.
33820B
27.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
82121
28.DISCONNECT ENGINE WIRE
Disconnect the transmission wire connector.
| *1 | Park/Neutral Position Switch Connector | *2 | Transmission Wire Connector |
| *3 | Transmission Revolution Sensor (NIN) Connector | *4 | Transmission Revolution Sensor (NOUT) Connector |
| *5 | Oil Pressure Sensor Connector | - | - |
Disconnect the transmission revolution sensor (NIN) connector.
Disconnect the park/neutral position switch connector.
Disconnect the transmission revolution sensor (NOUT) connector.
Disconnect the oil pressure sensor connector.
Disengage the 7 clamps to disconnect the engine wire from the continuously variable transaxle assembly.
Remove the bolt to disconnect the engine wire from the continuously variable transaxle assembly.
29.DISCONNECT WATER HOSE
Slide the 2 hose clips and disconnect the water hoses from the transmission oil cooler.
Disengage the 2 clamps to separate the water hose from the continuously variable transaxle assembly.
33823
30.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.
45100
31.SECURE STEERING WHEEL ASSEMBLY
45259A
32.REMOVE COLUMN HOLE COVER SILENCER SHEET
45260
33.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45025D
34.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
57533B
35.REMOVE FRONT FLOOR CENTER BRACE
17410
36.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
37.REMOVE FRONT DRIVE SHAFT ASSEMBLIES (for TMC Made)
38.REMOVE FRONT DRIVE SHAFT ASSEMBLIES (for TMMT Made)
39.INSTALL ENGINE HANGERS
Disengage the 3 clamps from the wire harness clamp bracket.
Remove the nut to separate the engine wire from the wire harness clamp bracket.
Remove the bolt and wire harness clamp bracket from the cylinder head sub-assembly.
Separate the bolts and No. 2 earth wire from the engine mounting insulator sub-assembly RH.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
|
Bolt |
Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-47060 |
| No. 2 Engine Hanger | 12282-47030 |
| Bolt | 91552-81030 |
40.INSTALL ENGINE SUPPORT BRIDGE
Remove the clip and the neck from the windshield washer jar assembly.
Install SST to the vehicle body as shown in the illustration.
| *a | Support Shaft | *b | Front Side Member |
| *c | Front Suspension Nut | - | - |
| *a | Support Shaft |
| *b | Front Side Member |
Make sure that no oil or grease is on the front side member, and set the support shaft on the level surface of the front side member.
The engine support bridge may fall off if any oil or grease is still on or it is installed on the unlevel surface.
Prevent SST from contacting the vehicle body exterior and windshield glass.
To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.
Lightly shake SST by hand to make sure it is securely installed before performing work.
| *a | Support Shaft |
| *b | Sub Beam |
| *c | Front Side Member |
| *d | Threaded Portion |
Turn the threaded portion of each support shaft to adjust its height until the sub beams are parallel to the ground.
Install the chain block to the sling bracket.
| *a | Chain Block | *b | Sling Bracket |
| *c | Fuse Shackle | *d | Shackle (A) |
Install the division bar to the chain block with the shackles.
| *a | Fuse Shackle |
| *b | Shackle (A) |
Make sure the fuse shackle is on the chain block side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.
If the fuse shackle is installed upside down, deformation of the fuse bolt will not be visible and cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with automatic transaxle assembly may fall.
| *a | Fuse Shackle |
| *b | Fuse Bolt |
Make sure that the fuse bolt of the fuse shackle is free of damage, such as deformation or cracks. If damaged, replace the fuse shackle.
If a deformed fuse bolt is used, it cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with transaxle assembly may fall.
Connect the division bar to the No. 1 engine hanger with the shackle (A) and chain.
| *1 | No. 1 Engine Hanger | *2 | No. 2 Engine Hanger |
| *a | Division Bar | *b | Shackle (A) |
| *c | Chain | - | - |
Connect the 2nd link of the chain to the No. 1 engine hanger.
Connect the division bar to the No. 2 engine hanger with the shackle (A) and chain.
Connect the 2nd link of the chain to the No. 2 engine hanger.
| *a | 120 mm (4.72 in.) or more |
Make sure the distance between the chain block assembly and suspension ring is 120 mm (4.72 in.) or more.
If the suspension height is less than 120 mm, adjust the links of the chain which connect the division bar and engine hanger.
Adjust the positions of the chain block assembly, support brackets and main beam so that the chain of the chain block assembly is perpendicular to the main beam and the length of the main beam on the outer side of the support bracket LH and RH is the same as shown in the illustration.
| *a | Chain Block | *b | Main Beam |
| *c | Dimension (A) | *d | Dimension (B) |
| *e | Right to Left Adjustment | *f | Front to Rear Adjustment |
To prevent the engine with automatic transaxle assembly from falling, make sure that the length of dimension (A) and dimension (B) are equal.
| *a | Main Beam |
Do not perform any procedures if the length of dimension (A) and dimension (B) are not equal.
Performing any procedure when the length of dimension (A) and dimension (B) are not equal may cause the engine assembly with automatic transaxle assembly and engine support bridge to fall, possibly causing serious injury.
Confirm the appropriate installation state of the engine support bridge and tighten the 6 wing bolts and 2 bolts.
| *a | Wing Bolt | *b | Bolt |
Do not perform any procedures before tightening the bolts to the specified torque.
Performing procedures without tightening the bolts to the specified torque, may cause the engine support bridge to fall.
| *a | Turn |
Tighten the chain block assembly until it cannot be moved any further by hand.
| *a | 41 N*m (418 kgf*cm, 30 ft.*lbf) or more |
When suspending the engine with automatic transaxle assembly, do not tighten the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf).
Tightening the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf) will cause the load capacity (400 kg (881.8 lb)) to be exceeded and may cause damage to the engine support bridge and vehicle body.
51108A
41.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
51107A
42.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
51201
43.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
12364B
44.REMOVE NO. 2 ENGINE MOVING CONTROL ROD
Remove the 4 bolts and No. 2 engine moving control rod from the continuously variable transaxle assembly.
30400
45.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
| *a | Lashing Belt |
Using a transmission jack, support the continuously variable transaxle assembly.
Adjust the attachment of the transmission jack to securely fix the continuously variable transaxle assembly to the transmission jack.
To prevent the transaxle oil (CVT) pan sub-assembly from deforming, do not place any attachments under the transaxle oil (CVT) pan sub-assembly of the continuously variable transaxle assembly.
Using a lashing belt or a rope, fix the continuously variable transaxle assembly to the transmission jack.
28100
46.REMOVE STARTER ASSEMBLY (for Valeo Made Cold Area Specification Vehicles)
28100
47.REMOVE STARTER ASSEMBLY (for Valeo Made except Cold Area Specification Vehicles)
28100
48.REMOVE STARTER ASSEMBLY (for Denso Made without Stop and Start System)
11363A
49.REMOVE FLYWHEEL HOUSING SIDE COVER
11361J
50.REMOVE FLYWHEEL HOUSING UNDER COVER
Remove the flywheel housing under cover from the stiffening crankcase assembly.
32101G
51.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.
There will be one black colored drive plate and torque converter assembly setting bolt.
12372A
52.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR
Remove the bolt and nut to separate the transverse engine engine mounting insulator from the engine mounting bracket LH.
Remove the nut and 4 bolts.
Remove the transverse engine engine mounting insulator from the vehicle body.
53.REMOVE ENGINE MOUNTING STAY LH
Remove the 2 bolts and engine mounting stay LH from the continuously variable transaxle assembly.
12325A
54.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET
Remove the 3 bolts and transverse engine engine mounting bracket from the continuously variable transaxle assembly.
30400
55.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
Remove the 7 bolts and continuously variable transaxle assembly from the engine assembly.
To prevent damage to the 2 knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.
Bolt (A): Remove from continuously variable transaxle assembly side.
Bolt (B): Remove from engine assembly side.
32000A
56.REMOVE TORQUE CONVERTER ASSEMBLY
Remove the torque converter assembly from the continuously variable transaxle assembly.
Remove the torque converter assembly from the input shaft horizontally.
30400E
57.REMOVE CVT OIL PUMP TYPE T OIL SEAL
Do not remove the front oil pump assembly from the CVT main body, as there is a possibility of the entry of dust and foreign matter.
Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which could prevent the vehicle from being able to be driven, could occur if dust or fine foreign matter enters the CVT.
Do not use cotton work gloves, cloths, or paper towels, etc. that may produce lint, dust or foreign matter.
Perform the operation as quickly as possible, as dust and foreign matter could enter the CVT while the torque converter assembly is removed.
Do not use an air gun until the torque converter assembly has been installed, as it could cause dust and foreign matter to be stirred up.
Clean the tips of both the claws of SST and the center bolt.
Using SST, remove the CVT oil pump type T oil seal.
Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles could be produced if they do.
58.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the 4 bolts and 4 wire harness clamp brackets from the continuously variable transaxle assembly.
87101A
59.REMOVE NO. 1 HEATER BRACKET SUB-ASSEMBLY
Separate the No. 1 breather plug (CVT) from the clamp.
Remove the clamp from the No. 1 heater bracket sub-assembly.
Remove the bolt and No. 1 heater bracket sub-assembly from the continuously variable transaxle assembly.
60.REMOVE STRAIGHT SCREW PLUG
Perform this procedure only when replacement of the straight screw plug is necessary.
Remove the straight screw plug and gasket from the continuously variable transaxle assembly.
35012B
61.REMOVE TRANSMISSION BREATHER HOSE SUB-ASSEMBLY
Perform this procedure only when replacement of the transmission breather hose sub-assembly is necessary.
Remove the transmission breather hose sub-assembly from the continuously variable transaxle assembly.
| *1 | No. 1 Breather Plug (CVT) |
| *2 | Breather Plug Hose |
| *3 | No. 2 Breather Plug (CVT) |
| *4 | O-ring |
Remove the No. 1 breather plug (CVT) and No. 2 breather plug (CVT) from the breather plug hose.
Remove the O-ring from the No. 2 breather plug (CVT).
32000A
62.INSPECT TORQUE CONVERTER ASSEMBLY
32101B
63.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY