Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER (for AWD) › 2016.10–2019.09
RM32H0E _53 Suspension _059601 REAR SUSPENSION _0292273 REAR SUSPENSION MEMBER(for AWD) A

REAR SUSPENSION  REAR SUSPENSION MEMBER(for AWD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Removal/installation of rear height control sensor sub-assembly LH*1 Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)*1
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


·

for 8NR-FTS:

(Click here)

·

for 3ZR-FAE:

(Click here)



*1: w/ Height Control Sensor


CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 41101 1.REMOVE REAR DIFFERENTIAL CARRIER SUB-ASSEMBLY

Hide 48812 2.REMOVE REAR STABILIZER BAR

Hide 51206A 3.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.

w/ Height Control Sensor:

i.
C365613

Disengage the clamp to separate the height control sensor wire harness.



b.
C365611

Disengage the 3 clamps to separate the differential carrier wire harness.


c.
C365610C01
2.323,3.479 2.646,3.042 true 2.094,3.594 2.302,2.885 true 1.688,3.74 1.292,4.333 true 0.833,3.917 0.573,4.333 true 2.865,3.573 2.625,3.781 true 2.906,3.396 3.219,3.594 0.313,0.198 10 true *a 2.688,2.865 2.927,3.063 0.24,0.198 10 true *b 2.302,2.635 2.563,2.844 0.26,0.208 10 true *b 1.146,4.365 1.458,4.563 0.313,0.198 10 true *b 0.417,4.375 0.729,4.573 0.313,0.198 10 true *b
*a Engine Lifter
*b Attachment
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:
·
C345782


·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.




d.

Remove the 2 bolts and 2 nuts.


e.

Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



Hide 48790 4.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 5.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 41651 6.REMOVE REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

a.

Using SST, remove the rear No. 1 differential mount cushion from the rear suspension member sub-assembly.

C365616C01
6.073,1.177 6.448,1.177 false 5.135,0.677 5.469,0.948 false 1.063,1.417 1.365,1.354 false 6.031,0.667 5.771,0.875 false 6.5,1.115 6.885,1.323 0.385,0.208 10 false SST 4.802,0.604 5.188,0.813 0.385,0.208 10 false SST 1.417,1.271 1.802,1.479 0.385,0.208 10 false SST 6.094,0.583 6.479,0.792 0.385,0.208 10 false *1
*1 Rear Suspension Member Sub-assembly - -
V100135

SST bolt location
V100136

Front of the Vehicle


SST
09316-12010  09570-24011  

NOTICE:
·

Apply grease to the threads and tip of the SST center bolt before use.

·

Be sure to use the correct combination of SST.

·

Make sure that SST (09316-12010) contacts the entire circumference of the rear No. 1 differential mount cushion.

·

Do not tilt the bolt of SST.

·

Do not bring SST (09316-12010) into contact with the rear suspension member sub-assembly.



HINT:

Install the SST bolt to the SST hole as shown in the illustration.



Hide 51284 7.REMOVE REAR SUSPENSION MEMBER HOLE COVER

a.
C365614C01
0.031,0.042 0.271,0.25 0.24,0.208 10 true *a 0.104,2.375 0.344,2.583 0.24,0.208 10 false *b
*a for LH Side
*b for RH Side


Remove the 4 rear suspension member hole covers from the rear suspension member sub-assembly as shown in the illustration.


Hide 8.REMOVE HOLE PLUG

a.
C365615

Remove the 8 hole plugs from the rear suspension member sub-assembly as shown in the illustration.