Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM32H0E _55 Steering _059605 POWER ASSIST SYSTEMS _0292301 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  CALIBRATION  


TORQUE SENSOR ZERO POINT CALIBRATION (USING GTS)


NOTICE:

Perform torque sensor zero point calibration if any of the following conditions occur:

·

The power steering ECU assembly has been replaced.

·

The electric power steering column sub-assembly has been replaced.

·

There is a difference in steering effort between turning left and right.



a.

Perform inspection before calibration.

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Calibrate the power steering ECU assembly. Enter the following menus: Chassis / EMPS / Data List.


vi.

Check the values by referring to the table below.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG Power Supply IG power source voltage Min.: 0.0000 V
Max.: 20.1531 V
8 to 16 V Ignition switch ON
Chassis > EMPS > Data List
Tester Display
IG Power Supply
50003 142 11
Standard Voltage:

8 to 16 V


NOTICE:

If the IG power supply voltage is 8 V or less, calibration cannot be performed. In this case, charge or replace the battery, and then perform calibration.




b.

Perform torque sensor zero point calibration.

NOTICE:

If DTC C1516 (Torque Sensor Zero Point Adjustment Incomplete) is stored, the torque sensor zero point cannot be calibrated. Clear the DTCs before starting calibration.


i.

Align the front wheels straight ahead and center the steering wheel.


ii.

Turn the ignition switch off.


iii.

Connect the GTS to the DLC3.


iv.

Turn the ignition switch to ON.


v.

Turn the GTS on.


vi.

Enter the following menus: Chassis / EMPS / Utility / Torque Sensor Adjustment.

Chassis > EMPS > Utility
Tester Display
Torque Sensor Adjustment
50005 142 224
NOTICE:
·

Do not turn the steering wheel sharply.

·

During the torque sensor zero point calibration the steering wheel will shudder. Do not touch the steering wheel until at least 3 seconds have elapsed after the shuddering has stopped.




vii.

Check for DTCs.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR

Chassis > EMPS > Trouble Codes
50001 142
NOTICE:

If DTC C1515, C1516, C1534 or C1581 is output, perform troubleshooting for the corresponding DTC.


Result:
Result See Procedure
DTC C1515 is output. (Click here)
DTC C1516 is output. (Click here)
DTC C1534 is output. (Click here)
DTC C1581 is output. (Click here)





ASSIST MAP WRITING (USING GTS)


NOTICE:

Perform assist map writing if the following condition occurs:

The power steering ECU assembly has been replaced.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Utility / Signal Check.

Chassis > EMPS > Utility
Tester Display
Signal Check
50005 142 3
HINT:
·

Follow the instructions on the GTS to perform Signal Check.

·

With DTC C1581 output, performing Signal Check will cause the power steering ECU assembly to enter Signal Check and the assist map will be written automatically.




f.

Wait for at least 5 seconds.


g.

Check for DTCs.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR

Chassis > EMPS > Trouble Codes
50001 142
HINT:

After writing the assist map, if DTC C1581 is output, perform the troubleshooting procedure for DTC C1581.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>C1581