This DTC will be stored if the power steering ECU assembly determines that the assist map is not written in the ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Return-to-normal Condition | Note |
|---|---|---|---|---|---|---|
| C1581 | Assist Map Number Un-Writing | Assist map not written in power steering ECU assembly | ·
CAN communication system ·
ECM ·
Main body ECU (Multiplex network body ECU) ·
Skid control ECU (Brake actuator assembly) ·
Power steering ECU assembly |
EPS warning light: Comes on | Assist Map Writing is performed or the ignition switch is turned ON again | - |
If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
Related parts store information necessary for assist map writing.
Related Part:
ECM
Main body ECU (Multiplex network body ECU)
Skid control ECU (Brake actuator assembly)
Perform assist map writing.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
| Tester Display |
|---|
| Signal Check |
Check for DTCs.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1581 is output. | A |
| DTC C1581 is not output. | B |
DTC C1581 is cleared after the assist map is written.
A
B
Check for DTCs.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output. | A |
| CAN communication system DTCs are output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Confirm if the related part has the correct part number.
| Related Part | ECM |
| Main body ECU (Multiplex network body ECU) | |
| Skid control ECU (Brake actuator assembly) |
When removing the related part to check it, be sure to follow the appropriate procedures and precautions.
ECM
for 8NR-FTS: Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>ECM>REMOVAL
Main body ECU (Multiplex network body ECU)
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Skid control ECU (Brake actuator assembly)
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
| Result | Proceed to |
|---|---|
| The related part has the correct part number. | A |
| The related part has an incorrect part number. | B |
A
B
Select Health Check on the GTS screen and check if system DTCs of the related part are output.
If system DTCs of the related part are stored, assist map writing to the power steering ECU assembly may not be performed properly.
| Result | Proceed to |
|---|---|
| System DTCs of the related part are output. | A |
| System DTCs of the related part are not output. (for LHD) | B |
| System DTCs of the related part are not output. (for RHD) | C |
A
B
C
Replace the related part with one that has the correct part number.
ECM
for 8NR-FTS: Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>ECM>REMOVAL
Main body ECU (Multiplex network body ECU)
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Skid control ECU (Brake actuator assembly)
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. (for LHD) | B |
| DTCs are output. (for RHD) | C |
A
B
C