Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2016.10–2019.09
RM32H0E _53 Suspension _059606 TIRE PRESSURE MONITORING _0292310 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2198/98  Initialization Switch (for Test Mode DTC)  


DESCRIPTION

The switch circuit inside the combination meter assembly turns on and off according to the steering pad switch assembly operation.

During test mode, when the steering pad switch assembly is operated, "TPMS" is selected on the multi-information display and the "ENTER" switch (steering pad switch assembly) is pressed, the tire pressure warning light illuminates, and when the "ENTER" switch (steering pad switch assembly) is not pressed, the tire pressure warning light blinks at 0.125 second intervals.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2198/98 Initialization Switch (for Test Mode DTC) Test mode procedure is performed.
·

Steering pad switch assembly

·

Spiral cable sub-assembly

·

Wire harness or connector

·

Tire pressure warning ECU and receiver


-

WIRING DIAGRAM

C376081E01
4.854,0.594 5.469,0.792 0.615,0.198 10 false CLSW 4.781,1.333 5.24,1.531 0.458,0.198 10 false M23 4.781,1.5 6.177,1.917 1.396,0.417 10 false Tire Pressure Warning ECU and Receiver 4.667,0.479 4.823,0.677 0.156,0.198 10 false 3 3.438,0.479 3.594,0.677 0.156,0.198 10 false 4 3.104,0.583 3.563,0.781 0.458,0.198 10 false INT 2.031,0.5 2.906,0.875 0.875,0.375 10 false Tire Pressure Warning Light 2.01,0.99 2.323,1.188 0.313,0.198 10 false ET 2.01,1.552 2.625,1.75 0.615,0.198 10 false MSSL 2.01,1.979 2.625,2.177 0.615,0.198 10 false MSM+ 1.76,0.885 2.073,1.083 0.313,0.198 10 false 21 1.76,1.448 2.073,1.646 0.313,0.198 10 false 33 1.76,1.865 2.073,2.063 0.313,0.198 10 false 28 1.615,2.188 1.927,2.385 0.313,0.198 10 false F4 1.604,2.344 3.563,2.552 1.958,0.208 10 false Combination Meter Assembly 3.469,2.74 3.927,2.938 0.458,0.198 10 false F29 3.469,3.167 3.927,3.365 0.458,0.198 10 false F29 3.469,3.552 3.927,3.75 0.458,0.198 10 false F29 4.906,2.729 5.365,2.927 0.458,0.198 10 false z1 4.906,3.146 5.365,3.344 0.458,0.198 10 false z1 4.906,3.542 5.365,3.74 0.458,0.198 10 false z1 5.115,3.896 6.385,4.281 1.271,0.385 10 false Steering Pad Switch Assembly 3.76,3.906 4.854,4.292 1.094,0.385 10 false Spiral Cable Sub-assembly 4.948,2.552 5.104,2.75 0.156,0.198 10 false 2 4.948,2.958 5.104,3.156 0.156,0.198 10 false 3 4.938,3.354 5.094,3.552 0.156,0.198 10 false 8 2.167,4.115 3.542,4.313 1.375,0.198 10 false to Ground 3.542,3.375 3.698,3.573 0.156,0.198 10 false 3 3.51,2.552 3.823,2.75 0.313,0.198 10 false 10 3.5,2.969 3.813,3.167 0.313,0.198 10 false 11 3.844,2.667 4.302,2.865 0.458,0.198 10 false +DP 3.844,3.063 4.458,3.26 0.615,0.198 10 false +DP2 3.844,3.448 4.302,3.646 0.458,0.198 10 false EAU

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F29 spiral cable sub-assembly connector.


b.

Disconnect the F4 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-10 (+DP) - F4-28 (MSM+) Always Below 1 Ω
F29-10 (+DP) or F4-28 (MSM+) - Body ground Always 10 kΩ or higher
F29-11 (+DP2) - F4-33 (MSSL) Always Below 1 Ω
F29-11 (+DP2) or F4-33 (MSSL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the M23 tire pressure warning ECU and receiver connector.


b.

Disconnect the F4 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M23-3 (CLSW) - F4-4 (INT) Always Below 1 Ω
M23-3 (CLSW) or F4-4 (INT) - Body ground Always 10 kΩ or higher
F4-21 (ET) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (INT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (INT)
a.

Disconnect the F4 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-4 (INT) - Body ground Ignition switch to ON 8 to 15 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER