Home › Engine / Hybrid System › 3ZR-FAE (ENGINE CONTROL) › SFI SYSTEM
RM32H0E _51 Engine / Hybrid System _059607 3ZR-FAE ENGINE CONTROL _0292315 SFI SYSTEM C

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  P0102  Mass Air Flow Circuit Low  P0103  Mass Air Flow Circuit High  


DESCRIPTION

The mass air flow meter is a sensor that measures the intake air volume using the following built-in components:

·

By-pass duct (allows some of the intake air to flow past a silicon chip sensor)

·

Silicon chip sensor (uses a heater control bridge circuit and temperature sensor bridge circuit to detect the difference in the temperature of the intake air that passes the sensors positioned before and after the heater).

·

Control circuit (converts the difference in temperature into a pulse signal and performs correction)


Intake air flows past the temperature sensor (before heater), the heater, and then the temperature sensor (after heater) of the silicon chip sensor in the by-pass duct. As the intake air is warmed up when it is exposed to the heater, the temperature of the intake air as it flows past the temperature sensor (after heater) is higher than when it flows past the temperature sensor (before heater). The difference in temperature of the intake air at each temperature sensor varies depending on the velocity of the intake air that flows past the silicon chip sensor. The temperature sensor bridge circuit detects the difference in temperature and the control circuit converts it into a pulse signal and outputs it to the ECM. When the temperature detected by the temperature sensor (before heater) is higher than that detected by the temperature sensor (after heater), backflow of the intake air is detected.

The ECM calculates the intake air volume based on the pulse signal received from the mass air flow meter, and uses it to determine the fuel injection duration necessary for an optimal air-fuel ratio.

The heater control bridge circuit has a temperature sensor and power transistor, and maintains the heater temperature at a specific temperature.

HINT:

When DTCs is stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM calculates the fuel injection duration based on the engine speed and throttle valve angle. Fail-safe mode continues until a pass condition is detected.


A403052C01
5.479,1.854 6.333,2.75 6.333,2.75 6.583,2.75 true 5.917,2.906 6.333,3.417 6.333,3.417 6.583,3.417 true 5.25,2.333 4.917,2.667 4.917,2.667 4.667,2.667 true 2.688,2.083 3.083,2.333 3.083,2.333 3.333,2.333 true 3.063,2 3.25,2.083 3.25,2.083 3.5,2.083 true 2.333,1.333 2.917,1.583 2.917,1.583 3.167,1.583 true 1.417,1.583 1.667,1.583 1.667,1.583 2.094,1.417 true 1.25,2.25 1.5,2.25 1.5,2.25 1.802,2.083 true 4.667,0.583 4.917,0.75 0.25,0.167 10 false *1 6.667,2.677 6.917,2.833 0.25,0.156 10 false *a 4.5,2.583 4.75,2.75 0.25,0.167 10 false *b 3.25,1.51 3.5,1.667 0.25,0.156 10 false *c 1.25,1.5 1.5,1.667 0.25,0.167 10 false *d 3.583,2.01 3.896,2.167 0.313,0.156 10 false *e 3.417,2.26 3.729,2.417 0.313,0.156 10 false *f 1.083,2.167 1.333,2.323 0.25,0.156 10 false *g 6.667,3.344 6.917,3.5 0.25,0.156 10 false *h
*1 Mass Air Flow Meter - -
*a Silicon Chip Sensor *b By-pass Duct
*c Heater *d Heater Thermistor
*e Intake Air *f Temperature Sensor (After Heater)
*g Temperature Sensor (Before Heater) *h Air Flow


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0102 Mass Air Flow Circuit Low The mass air flow meter output frequency is less than 0.1 kHz for 3 seconds
(1 trip detection logic)
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored
P0103 Mass Air Flow Circuit High The mass air flow meter output frequency is higher than 9.8 kHz for 3 seconds.
(1 trip detection logic)
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter, the frequency level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter circuit and stores a DTC.

Example:

When the sensor output frequency remains less than 0.1 kHz, or higher than 9.8 kHz for 3 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Turn the GTS on.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P0102 or P0103.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A384876E01
0.635,3.188 0.948,3.385 0.313,0.198 10 false C5 0.635,3.375 2.031,3.635 1.396,0.26 10 false Mass Air Flow Meter 1.833,2.375 2.292,2.573 0.458,0.198 10 false THA 1.844,1.844 2.302,2.042 0.458,0.198 10 false E2G 1.906,1.24 2.219,1.438 0.313,0.198 10 false FG 1.823,0.667 2.281,0.865 0.458,0.198 10 false VCC 2.219,0.667 2.375,0.865 0.156,0.198 10 false 3 2.177,1.271 2.333,1.469 0.156,0.198 10 false 1 2.219,1.844 2.375,2.042 0.156,0.198 10 false 2 2.24,2.406 2.396,2.604 0.156,0.198 10 false 4 5.708,3.219 6.167,3.417 0.458,0.198 10 false C63 5.698,3.385 6.156,3.583 0.458,0.198 10 false ECM 5.167,0.667 5.781,0.865 0.615,0.198 10 false VCVG 5.177,1.24 5.49,1.438 0.313,0.198 10 false VG 5.188,1.844 5.646,2.042 0.458,0.198 10 false E2G 5.188,2.396 5.646,2.594 0.458,0.198 10 false THA 6.031,1.063 6.188,1.26 0.156,0.198 10 false R 6.104,0.354 6.563,0.552 0.458,0.198 10 false 5 V 4.875,0.677 5.333,0.875 0.458,0.198 10 false 103 4.865,1.25 5.323,1.448 0.458,0.198 10 false 137 4.875,1.844 5.49,2.042 0.615,0.198 10 false 104 4.875,2.396 5.333,2.594 0.458,0.198 10 false 138

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER)
A353757C05
0.25,0.906 0.75,1.156 0.5,0.25 0.917,1.75 1.375,1.313 true 1.667,1.896 1.667,1.292 true 2.302,1.823 1.885,1.302 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.406,0.927 0.802,1.177 0.396,0.25 10 false C5 0.781,1.771 1.177,2.021 0.396,0.25 10 false FG 1.542,1.927 2,2.167 0.458,0.24 10 false E2G 2.271,1.875 2.667,2.125 0.396,0.25 10 false VCC
*a Front view of wire harness connector
(to Mass Air Flow Meter)


a.

Disconnect the mass air flow meter.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C5-3 (VCC) - C5-2 (E2G) Ignition switch ON 4.8 to 5.2 V
C5-1 (FG) - C5-2 (E2G) Ignition switch ON 4.8 to 5.2 V



Result:
Proceed to
OK
NG



OK

2.INSPECT MASS AIR FLOW METER

NG

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
2.INSPECT MASS AIR FLOW METER

Result:
Proceed to
NEXT



NEXT

3.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0102 AND P0103 ARE OUTPUT AGAIN)
3.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0102 AND P0103 ARE OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

j.

Read the DTCs.

Result:
Result Proceed to
DTC P0102 and/or P0103 is output A
DTCs are not output B




A

B

END

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the C5 mass air flow meter connector.


b.

Disconnect the C63 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C63-103 (VCVG) - C5-3 (VCC) Always Below 1 Ω
C63-137 (VG) - C5-1 (FG) Always Below 1 Ω
C63-104 (E2G) - C5-2 (E2G) Always Below 1 Ω
C63-103 (VCVG) or C5-3 (VCC) - Body ground and other terminals Always 10 kΩ or higher
C63-137 (VG) or C5-1 (FG) - Body ground and other terminals Always 10 kΩ or higher
C63-104 (E2G) or C5-2 (E2G) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - ECM)