Home › Drivetrain › K114 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE FLUID
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292451 CONTINUOUSLY VARIABLE TRANSAXLE FLUID N

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE FLUID  ADJUSTMENT  


PROCEDURE

Hide 1. PRECAUTIONS AND WORK DESCRIPTION

a.

The K114 continuously variable transaxle assembly does not have an oil filler tube or oil level gauge. When adding fluid, add fluid through the refill hole in the continuously variable transaxle assembly. The fluid level can be adjusted by draining excess fluid (allowing excess fluid to overflow) through the No. 1 transmission oil filler tube of the transaxle oil (CVT) pan sub-assembly.

HINT:

"Overflow" indicates the condition under which fluid comes out of the overflow plug hole.



b.

When adding fluid, add the specified amount of fluid while the engine assembly is cold. Then, warm up the engine assembly to circulate the fluid in the continuously variable transaxle assembly and adjust the fluid level with the engine idling at the specified fluid temperature.


c.

The K114 continuously variable transaxle assembly requires Toyota Genuine CVT fluid FE.


d.

When adjusting the fluid level, park the vehicle on level ground (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).


e.

When adjusting the fluid level, turn off all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, to reduce load.


f.

The fluid temperature in the text indicates "A/T Oil Temperature 1" displayed on the GTS.


g.

Fluid level adjustment should be performed according to the following procedure and notes.

C202513E16
1.875,2.333 2.719,2.594 2.719,2.594 2.719,2.708 false 5.625,2.385 6.135,2.656 6.135,2.656 6.135,2.813 false 1.552,3.396 4.271,3.76 2.719,0.365 12 false 3. ADJUST FLUID TEMPERATURE 0.302,5.781 2.25,6.125 1.948,0.344 12 false 4. ADJUST FLUID LEVEL 0.063,0 2.146,0.344 2.083,0.344 12 false Fluid Filling Procedure: 0.063,0.344 2.313,1.073 2.25,0.729 12 false 1. PERFORM INITIAL FILLING (when necessary) 4.021,0.344 7.083,0.573 3.063,0.229 12 false 2. ADD SPECIFIED AMOUNT OF FLUID 0.052,1.083 2.01,1.26 1.958,0.177 10 false Add fluid to the specified level. 4.208,0.792 6.875,1.188 2.667,0.396 10 false Add the correct amount of fluid specified for the operation that was performed. 0.219,2.552 1.354,3.563 1.135,1.01 10 false Add fluid until fluid comes out of the overflow plug hole. 0.146,7.708 1.927,8.708 1.781,1 10 false Keep the overflow plug open until the fluid flow slows and only drips come out. 0.302,6.188 2.688,6.667 2.385,0.479 10 false Drain excess fluid at the specified fluid temperature. 4.281,6.073 6.708,6.719 2.427,0.646 10 false If no fluid comes out, add fluid until fluid comes out of the overflow plug hole. 1.542,3.813 6.885,4.552 5.344,0.74 10 false Start the engine to circulate the fluid. Enter fluid temperature detection mode and engine idle speed control mode, and adjust the fluid temperature to the specified level. 6.365,1.771 7.042,2.323 0.677,0.552 10 false Specified Amount of Fluid 2.094,2.698 3.333,3.302 1.24,0.604 10 false No. 1 Transmission Oil Filler Tube 5.729,2.823 6.635,3.021 0.906,0.198 10 false Overflow Plug


Hide 2. WORK FLOW

a.

The adjustment should be performed according to the procedures referenced in the work flow below.

C357692E03
3.375,0.094 4.146,0.292 0.771,0.198 10 false START 0.104,0.031 1.417,0.271 1.313,0.24 10 false WORK FLOW: 2.667,0.615 4.99,0.896 2.323,0.281 10 false [STEP4] Perform Initial Filling 0.146,0.969 3.063,1.25 2.917,0.281 10 false Operations that require initial filling: 0.167,1.25 3.75,1.75 3.583,0.5 8 false Removal and installation of the transaxle oil (CVT) pan sub-assembly or fluid drain and refill 0.167,1.75 3.75,2 3.583,0.25 8 false Removal and installation of the front drive shaft assembly 0.167,2 3.75,2.25 3.583,0.25 8 false Replacement of the front drive shaft oil seal 0.167,2.25 3.75,2.5 3.583,0.25 8 false Removal and installation of the transmission oil cooler 0.167,2.5 3.75,2.75 3.583,0.25 8 false Removal and installation of the torque converter assembly 0.167,2.75 4,3 3.833,0.25 8 false Replacement of the continuously variable transaxle assembly 3.938,0.969 7.094,1.25 3.156,0.281 10 false Operations that do not require initial filling: 3.99,1.25 6.813,1.5 2.823,0.25 8 false Repair of a fluid leak, etc. 3.99,1.5 6.99,1.917 3,0.417 8 false Replacement of the continuously variable transaxle assembly with torque converter assembly to a new one 2.5,3.25 5.323,3.5 2.823,0.25 10 false [STEP5] Add Specified Amount of Fluid 2.479,3.792 5.333,4.042 2.854,0.25 10 false [STEP6, 7] Adjust the Fluid Temperature 1.323,4.188 5.969,4.542 4.646,0.354 10 false Enter fluid temperature detection mode and engine idle speed control mode 2.844,4.677 4.427,5.073 1.583,0.396 10 false Idling (Warm up the fluid) 3.125,5.208 4.125,5.719 1,0.51 10 false Check the fluid temperature 5.917,4.698 6.938,5.406 1.021,0.708 10 false Stop the engine and wait until the fluid temperature drops 2.552,6.073 4.74,6.417 2.188,0.344 10 false Fluid level adjustment temperature 4.156,5.375 5.76,5.813 1.604,0.438 10 false Above fluid level adjustm ent temperature 1.385,5.385 2.99,5.823 1.604,0.438 10 false Below fluid level adjustm ent temperature 2.76,6.729 4.948,7.073 2.188,0.344 10 false [STEP8] Adjust Fluid Level 3.073,7.115 5.26,7.458 2.188,0.344 10 false Drain excess fluid 2.865,7.698 5.052,8.042 2.188,0.344 10 false Check the amount of fluid 0.344,7.677 1,7.99 0.656,0.313 10 false Add fluid 6.375,7.688 7.031,8 0.656,0.313 10 false Overflow 4.865,7.885 5.948,8.104 1.083,0.219 10 false Fluid comes out 1.271,7.896 2.594,8.156 1.323,0.26 10 false No fluid comes out 1.823,8.5 5.979,8.802 4.156,0.302 10 false [STEP9] Perform ATF Thermal Degradation Estimate Reset 2.917,9.042 7.073,9.344 4.156,0.302 10 false [STEP10] Rebuild Work 3.458,9.521 3.813,9.802 0.354,0.281 10 false END


Hide 3. BEFORE FILLING TRANSAXLE WITH FLUID

NOTICE:

If the continuously variable transaxle assembly is hot (fluid temperature is high), wait until the fluid temperature becomes the same as the ambient temperature before starting the following procedure (recommended fluid temperature: approximately 20°C (68°F)).


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).



b.

c.

Remove the rear engine under cover LH.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


Hide 4. PERFORM INITIAL FILLING

NOTICE:

After performing either of the following operations, it is not necessary to perform the initial filling procedure. Proceed to Add Specified Amount of Fluid (Step 5).


Operations that do not Require Initial Filling
·

Removal and installation of the oil cooler or an oil cooler hose.

·

Repair of a fluid leak, etc.



a.
C362022

Remove the refill plug and gasket from the continuously variable transaxle assembly.


b.
C362023

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle oil (CVT) pan sub-assembly.

NOTICE:
·

If fluid comes out after removing the overflow plug, wait until the fluid flow slows and only drips come out.

·

If fluid comes out, it is not necessary to perform the initial filling procedure. After checking the tightening torque of the No. 1 transmission oil filler tube, temporarily install the overflow plug.




c.
C365127C01
2.771,0.521 2.917,0.625 false 2.594,0.427 2.906,0.625 0.313,0.198 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, check that the No. 1 transmission oil filler tube is tightened to the specified torque.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)

NOTICE:

If the No. 1 transmission oil filler tube is not tightened to the specified torque, the amount of fluid cannot be precisely adjusted.


HINT:

To check the torque of the No. 1 transmission oil filler tube, insert a 6 mm hexagon socket wrench into the overflow plug hole.



d.

Perform initial filling.

i.
C365128

Add fluid to the refill hole until it flows out of the overflow plug hole.

NOTICE:

Use Toyota Genuine CVT fluid FE.




e.
C365129

Wait until the fluid flow slows and only drips come out.


f.
C362023

Using a 6 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle oil (CVT) pan sub-assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.



g.
C362022

Temporarily install the gasket and refill plug to the continuously variable transaxle assembly.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



Hide 5.ADD SPECIFIED AMOUNT OF FLUID

a.
C362022

Remove the refill plug and gasket from the continuously variable transaxle assembly.


b.
C365126

Fill fluid into the refill hole with the correct amount of fluid as listed in the table below.

NOTICE:

Use Toyota Genuine CVT fluid FE.


HINT:

The refill amount differs depending on the operation that was performed.


Standard Capacity:
Operation Performed Fill Amount
Replacement of the continuously variable transaxle assembly (when replacing the torque converter assembly with a new one) 4.1 liters (4.3 US qts, 3.6 Imp. qts)
Replacement of the continuously variable transaxle assembly (when reusing the torque converter assembly) 4.1 liters (4.3 US qts, 3.6 Imp. qts)
Removal and installation of the transaxle oil (CVT) pan sub-assembly (with fluid drain) 2.0 liters (2.1 US qts, 1.8 Imp. qts)
Drain and refill of fluid
Removal and installation of a front drive shaft assembly
Removal and installation of the torque converter assembly (when replacing the torque converter assembly with a new one) 3.0 liters (3.2 US qts, 2.6 Imp. qts)
Removal and installation of the torque converter assembly (when reusing the torque converter assembly) 2.5 liters (2.6 US qts, 2.2 Imp. qts)
Repair of a fluid leak, etc. 0.6 liters (0.6 US qts, 0.5 Imp. qts)
Removal and installation of the oil cooler or an oil cooler hose



c.
C362022

Temporarily install the gasket and refill plug to the continuously variable transaxle assembly to avoid fluid spillage.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



d.

Lower the vehicle.


Hide 6.ADJUST FLUID TEMPERATURE (when Using the GTS)

a.

Connect the GTS to the DLC3 with the ignition switch off.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fans and audio system, are off.



c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
A/T Oil Temperature 1
50004 234 13 406

d.

According to the display on the GTS, perform the Active Test "Connect the TC and TE1 / ON".

HINT:

The indicator lights on the combination meter blink to indicate that a DTC has been stored when the Active Test "Connect the TC and TE1 / ON" is performed.



e.

Select the Data List item: A/T Oil Temperature 1.


f.

Depress and hold the brake pedal.


g.

Start the engine.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, are off.



h.

Slowly move the shift lever from P to D, and then back to P (keep the shift lever in each position for approximately 3 seconds).

HINT:

Slowly move the shift lever to circulate the fluid through each part of the continuously variable transaxle assembly.



i.
C364037C03
0.104,2.885 0.333,3.083 0.229,0.198 10 false *a 0.104,3.948 0.417,4.146 0.313,0.198 10 false *b 1.344,2.448 1.656,2.646 0.313,0.198 10 false *f 1.323,3.5 1.635,3.698 0.313,0.198 10 false *d 2.323,3.5 2.635,3.698 0.313,0.198 10 false *e 2.25,4.25 2.563,4.448 0.313,0.198 10 false *c
*a Shift Position
*b Indication of Shift Position
*c Fluid Temperature Detection Mode
*d 6 sec. or more
*e 2 sec.
*f Less than 1.5 sec.


While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for 1.5 seconds or more.


HINT:

Performing this operation will cause the vehicle to enter fluid temperature detection mode.



j.
C364039

Check that the D shift indicator comes on for 2 seconds.

HINT:
·

When fluid temperature detection mode is activated, the D shift indicator on the combination meter comes on for 2 seconds.

·

If the D shift indicator does not come on for 2 seconds, return to the first step (perform the Active Test "Connect the TC and TE1 / ON") and perform the procedure again.




k.

Move the shift lever to P.


l.

Release the brake pedal.


m.

According to the display on the GTS, perform the Active Test "Connect the TC and TE1 / OFF".

NOTICE:

Make sure that terminals are not connected. If the terminals are connected, the fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Disconnecting the terminals activates engine idle speed control mode.

·

In engine idle speed control mode, engine idle speed control starts when the fluid temperature reaches the specified temperature and the engine speed is maintained.

·

Even after the terminals are disconnected, fluid temperature detection mode remains active until the ignition switch is turned off.




n.

Adjust the fluid temperature to the fluid level adjustment temperature.

i.

Check the fluid temperature by monitoring the D shift indicator.

Relationship between Fluid Level Adjustment Temperature and the D Shift Indicator:
Below Fluid Level Adjustment Temperature Fluid Level Adjustment Temperature Above Fluid Level Adjustment Temperature
Fluid Temperature ("A/T Oil Temperature 1" displayed on the GTS) 35°C (95°F) or less 35 to 45°C (95 to 113°F) 45°C (113°F) or more
D Shift Indicator Off On Blinks


HINT:
·

In fluid temperature detection mode, the D shift indicator comes on, goes off, or blinks depending on the fluid temperature.

·

The fluid filling procedure should be performed when the D shift indicator is on (the fluid temperature is within the fluid level adjustment temperature range).




ii.

If the D shift indicator is on [Fluid Level Adjustment Temperature: 35 to 45°C (95 to 113°F)]: Immediately proceed to the Adjust Fluid Level (Step 9).


iii.

Adjust the fluid temperature.

1.

If the D shift indicator is off [Below Fluid Level Adjustment Temperature: 35°C (95°F) or less]: Warm up the engine with the engine idling in engine idle speed control mode until the D shift indicator turns on.

2.

If the D shift indicator is on [Fluid Level Adjustment Temperature: 35 to 45°C (95 to 113°F)]: Immediately proceed to Adjust Fluid Level (Step 9).

3.

If the D shift indicator is blinking [Above Fluid Level Adjustment Temperature: 45°C (113°F) or more]: Stop the engine and wait until the fluid temperature drops to 35°C (95°F) or less (the D shift indicator goes off). Then perform the adjust fluid temperature procedure again from the beginning.




Hide 7.ADJUST FLUID TEMPERATURE (when Not Using the GTS)

a.
C166029C73
1.333,1.927 1.771,1.479 true 1.583,0.896 2.021,0.448 true 1.125,1.844 1.365,2.021 0.24,0.177 10 false TC 2.063,0.344 2.427,0.521 0.365,0.177 10 false CG 0.125,0.073 0.344,0.25 0.219,0.177 10 false *1
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the ignition switch off.

SST
09843-18040  


b.

Depress and hold the brake pedal.


c.

Start the engine.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, are off.



d.

Slowly move the shift lever from P to D, and then back to P (keep the shift lever in each position for approximately 3 seconds).

HINT:

Slowly move the shift lever to circulate the fluid through each part of the continuously variable transaxle assembly.



e.
C364037C04
0.104,2.885 0.333,3.083 0.229,0.198 10 false *a 0.104,3.948 0.417,4.146 0.313,0.198 10 false *b 1.344,2.448 1.656,2.646 0.313,0.198 10 false *f 1.323,3.5 1.635,3.698 0.313,0.198 10 false *d 2.323,3.5 2.635,3.698 0.313,0.198 10 false *e 2.25,4.25 2.563,4.448 0.313,0.198 10 false *c
*a Shift Position
*b Indication of Shift Position
*c Fluid Temperature Detection Mode
*d 6 sec. or more
*e 2 sec.
*f Less than 1.5 sec.


While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for 1.5 seconds or more.


HINT:

Performing this operation will cause the vehicle to enter fluid temperature detection mode.



f.
C364039

Check that the D shift indicator comes on for 2 seconds.

HINT:
·

When fluid temperature detection mode is activated, the D shift indicator on the combination meter comes on for 2 seconds.

·

If the D shift indicator does not come on for 2 seconds, return to the first step (connect terminals 13 (TC) and 4 (CG) of the DLC3) and perform the procedure again.




g.

Move the shift lever to P.


h.

Release the brake pedal.


i.

Remove SST from terminals 13 (TC) and 4 (CG).

NOTICE:

Make sure that the terminals are not connected. If the terminals are connected, the fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Disconnecting the terminals activates engine idle speed control mode.

·

In engine idle speed control mode, engine idle speed control starts when the fluid temperature reaches the specified temperature and the engine speed is maintained.

·

Even after the terminals are disconnected, fluid temperature detection mode is active until the ignition switch is turned off.




j.

Adjust the fluid temperature to the fluid level adjustment temperature.

i.

Check the fluid temperature by monitoring the D shift indicator.

Relationship between Fluid Level Adjustment Temperature and the D Shift Indicator:
Below Fluid Level Adjustment Temperature Fluid Level Adjustment Temperature Above Fluid Level Adjustment Temperature
Fluid Temperature ("A/T Oil Temperature 1" displayed on the GTS) 35°C (95°F) or less 35 to 45°C (95 to 113°F) 45°C (113°F) or more
D Shift Indicator Off On Blinks


HINT:
·

In fluid temperature detection mode, the D shift indicator comes on, goes off, or blinks depending on the fluid temperature.

·

The fluid filling procedure should be performed when the D shift indicator is on (the fluid temperature is within the fluid level adjustment temperature range).




ii.

If the D shift indicator is on [Fluid Level Adjustment Temperature: 35 to 45°C (95 to 113°F)]: Immediately proceed to the Adjust Fluid Level (Step 9).


iii.

Adjust the fluid temperature.

1.

If the D shift indicator is off [Below Fluid Level Adjustment Temperature: 35°C (95°F) or less]: Warm up the engine with the engine idling in engine idle speed control mode until the D shift indicator turns on.

2.

If the D shift indicator is on [Fluid Level Adjustment Temperature: 35 to 45°C (95 to 113°F)]: Immediately proceed to Adjust Fluid Level (Step 9).

3.

If the D shift indicator is blinking [Above Fluid Level Adjustment Temperature: 45°C (113°F) or more]: Stop the engine and wait until the fluid temperature drops to 35°C (95°F) or less (the D shift indicator goes off). Then perform the adjust fluid temperature procedure again from the beginning.




Hide 8.ADJUST FLUID LEVEL

CAUTION:

Use caution, as the fluid is hot while the engine is idling and the radiator fan is operating.


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).



b.
C362023

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle oil (CVT) pan sub-assembly.

CAUTION:

Be careful as the fluid coming out of the overflow plug hole is hot.



c.

Check the amount of fluid that comes out of the overflow plug hole.

NOTICE:

If only a small amount of fluid (approximately 5 cc (0.3 cu. in.)) comes out of the overflow plug hole, then only fluid remaining in the No. 1 transmission oil filler tube has come out. This is not considered to be overflow.


·

If the amount of fluid that comes out of the overflow plug hole is large, proceed to *1.

·

If no fluid comes out of the overflow plug hole, proceed to *2.



d.
C365129

*1: If the amount of fluid that comes out of the overflow plug hole is large, wait until the fluid flow slows and only drips come out.

HINT:

The fluid flow will not stop completely because the fluid continues to expand as its temperature increases.



e.
C365128

*2: If no fluid comes out of the overflow plug hole, remove the refill plug and gasket. Then add fluid through the refill hole until fluid comes out of the overflow plug hole. Wait until the fluid flow slows and only drips come out.

NOTICE:

Use Toyota Genuine CVT fluid FE.



f.
C362023

Using a 6 mm hexagon socket wrench, install a new gasket and the overflow plug to the transaxle oil (CVT) pan sub-assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


g.
C362022

Install a new gasket and the refill plug to the continuously variable transaxle assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


h.

Lower the vehicle.


i.

Turn the ignition switch off.

HINT:

Turning the ignition switch off exits fluid temperature detection mode.



j.

Remove the GTS from the DLC3 (when using the GTS).


Hide 9.PERFORM ATF THERMAL DEGRADATION ESTIMATE RESET

NOTICE:

If approximately 50% or more of the CVT fluid has been replaced during a repair of the transaxle or a similar operation, perform ATF Thermal Degradation Estimate Reset.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


Hide 10. REBUILD WORK

a.

Lift the vehicle.


b.

Clean each part.


c.

Check for fluid leaks.


d.

e.

f.

Lower the vehicle.