Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › ENGINE ASSEMBLY
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0292817 ENGINE ASSEMBLY A

3ZR-FAE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 2.REMOVE ENGINE FROM ENGINE STAND

a.

Remove the engine assembly from the engine stand.


Hide 3.INSTALL COMPRESSOR WITH PULLEY ASSEMBLY

Hide 16361A 5.INSTALL FAN AND GENERATOR V BELT

Hide 32101B 6.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 16281F 8.INSTALL NO. 5 WATER BY-PASS HOSE

a.

Install the No. 5 water by-pass hose to the No. 3 water by-pass pipe and oil cooler and slide the 2 clips to secure it.


b.

Engage the 2 clamps.


Hide 16267 9.INSTALL NO. 3 WATER BY-PASS HOSE

a.

Install the No. 3 water by-pass hose to the cylinder head sub-assembly and oil cooler and slide the 2 clips to secure it.


b.

Engage the clamp.


Hide 82121 10.INSTALL ENGINE WIRE

a.

Connect all the connectors and clamps, and install the engine wire to the engine assembly with transaxle.


Hide 11363A 11.INSTALL FLYWHEEL HOUSING SIDE COVER

a.

Install the flywheel housing side cover to the cylinder block sub-assembly.


Hide 28100 12.INSTALL STARTER ASSEMBLY

Hide 12305 13.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A393425C01
0.313,2.188 0.948,2.406 0.635,0.219 10 true 1 (*a), 3 1.021,0.563 1.177,0.76 0.156,0.198 10 true 4 2.635,1.781 2.792,1.979 0.156,0.198 10 true 3
*a Temporarily Tighten


Temporarily install the engine mounting insulator sub-assembly RH to the vehicle.


b.

Install the 2 bolts and nut in the order shown in the illustration.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


c.

Connect the air conditioner tube and accessory assembly to the engine mounting insulator sub-assembly RH with the bolt and nut.

Torque:
Bolt : 9.8 N*m (100 kgf*cm, 87 in.*lbf)
Nut : 5.4 N*m (55 kgf*cm, 48 in.*lbf)


d.

Install the No. 2 earth wire to the engine mounting insulator sub-assembly RH and vehicle with the 2 bolts.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


Hide 12372A 14.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A393423C01
0.51,0.552 1.063,0.76 0.552,0.208 10 true 1 (*a), 5 2.427,1.917 2.583,2.115 0.156,0.198 10 true 2 2.427,1.156 2.583,1.354 0.156,0.198 10 true 4 2.167,0.073 2.323,0.271 0.156,0.198 10 true 6 0.5,1.26 0.656,1.458 0.156,0.198 10 true 3
*a Temporarily Tighten


Temporarily install the engine mounting insulator LH to the vehicle.


b.

Install the 4 bolts and nut in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 16.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket with the bolt.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


b.

Connect the air fuel ratio sensor connector.


c.

Engage the 5 clamps.


Hide 17.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




b.

Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




c.

Connect the front suspension crossmember sub-assembly to the vehicle with the 6 bolts.

Torque:
141 N*m (1438 kgf*cm, 104 ft.*lbf)


d.

Install the engine mounting insulator LH to the engine mounting bracket LH with the bolt and nut.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

While holding the nut in place, tighten the bolt.



e.

Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut.

Torque:
Bolt : 72 N*m (734 kgf*cm, 53 ft.*lbf)
Nut : 41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 51108A 18.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 19.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 17410 23.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst)

Hide 57533B 24.INSTALL FRONT FLOOR CENTER BRACE

Hide 45025D 25.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 26.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 27.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 88704 28.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88703 29.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 23901 30.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube connector to the fuel pipe.

CAUTION:

Align the fuel tube connector with the fuel pipe, then push the fuel tube connector in until the retainer makes a "click" sound. If it is difficult to push the fuel tube connector in, apply a small amount of engine oil to the tip of the fuel pipe. After connecting, pull the fuel pipe and fuel tube connector to make sure that they are securely connected.



b.

Engage the claw and install the No. 1 fuel pipe clamp.


Hide 87245 31.CONNECT INLET HEATER WATER HOSE

a.

Connect the inlet heater water hose to the No. 1 water by-pass pipe and slide the clip to secure it.


Hide 87246 32.CONNECT OUTLET HEATER WATER HOSE

a.

Connect the outlet heater water hose to the No. 3 water by-pass hose and slide the clip to secure it.


b.

Engage the clamp.


Hide 44750 33.CONNECT UNION TO CONNECTOR TUBE HOSE

a.

Connect the union to connector tube hose to the vacuum pump assembly and slide the clip to secure it.


Hide 23829A 34.CONNECT FUEL VAPOR FEED HOSE

a.

Connect the fuel vapor feed hose to the purge valve (purge VSV) and slide the clip to secure it.


Hide 16572D 36.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet and slide the clip to secure it.


Hide 16571C 37.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the cylinder head sub-assembly and slide the clip to secure it.


Hide 74404A 38.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Install the air battery clamp sub-assembly to the vehicle with the 3 bolts.

Torque:
15.4 N*m (157 kgf*cm, 11 ft.*lbf)


b.

Engage the clamp to connect the engine wire to the battery clamp sub-assembly.


Hide 39.CONNECT WIRE HARNESS

a.

Connect the engine wire to the transaxle assembly with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


b.

Connect the engine wire to the positive (+) battery terminal with the 3 nuts.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


c.

Connect the engine wire to the battery clamp sub-assembly with the bolt and nut.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


d.
A397426C01
2.667,0.375 3.042,0.615 0.375,0.24 12 false *A 2.688,1 3.063,1.24 0.375,0.24 12 false *B
*A for Type A
*B for Type B


Connect the engine wire to the vehicle with the 2 bolts.

Torque:
for Type A : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
for Type B : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)


Hide 28800 41.INSTALL BATTERY

Hide 43.ADD ENGINE COOLANT

Hide 44.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 45.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 49.INSPECT FOR ENGINE OIL LEAK

Hide 51.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK

Hide 56.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR TANK

Hide 51444A 57.INSTALL REAR ENGINE UNDER COVER LH

a.

Install the rear engine under cover LH to the vehicle with the 6 clips.


Hide 51443C 58.INSTALL REAR ENGINE UNDER COVER RH

a.

Install the rear engine under cover RH to the vehicle with the 6 clips.


Hide 51441 59.INSTALL NO. 1 ENGINE UNDER COVER

a.
A390450C01
0.854,0 1.083,0.198 0.229,0.198 10 true *1 1.396,0.01 1.625,0.208 0.229,0.198 10 true *1 1.875,0.01 2.104,0.208 0.229,0.198 10 true *1 2.417,0 2.646,0.198 0.229,0.198 10 true *1
*1 Bolt


Install the No. 1 engine under cover to the vehicle with the 4 bolts, 4 screws and 4 clips.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 60.INSTALL FRONT WHEELS

Hide 61. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 62.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 11212 67.INSTALL NO. 2 CYLINDER HEAD COVER