The ECM of this system is connected to the CAN communication system. Therefore, before starting troubleshooting, be sure to check that there are no malfunctions in the CAN communication system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Refer to How to Troubleshoot ECU Controlled Systems in Introduction.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| NEXT |
NEXT
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding.
| Proceed to |
|---|
| NEXT |
NEXT
Use the GTS to check if the CAN communication system is functioning normally.
Refer to CAN Bus Check for the CAN communication system.
The ECM is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there are no malfunctions in the CAN communication system.
| Result | Proceed to |
|---|---|
| CAN communication DTCs are not output. | A |
| CAN communication DTCs are output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Refer to DTC Check/Clear.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Refer to Check Mode Procedure.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>CHECK MODE PROCEDURE
| Proceed to |
|---|
| NEXT |
NEXT
Proceed to DTC Check/Clear.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Refer to Continuously Variable Transaxle Fluid.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE FLUID>ADJUSTMENT
Refer to Park/Neutral Position Switch.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>PARK / NEUTRAL POSITION SWITCH>ON-VEHICLE INSPECTION
Refer to Shift Lever.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>SHIFT LEVER>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Refer to Road Test.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Refer to Mechanical System Tests.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>MECHANICAL SYSTEM TESTS
Refer to Hydraulic Test.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>HYDRAULIC TEST
| Result | Proceed to |
|---|---|
| Symptom does not occur | A |
| Symptom occurs | B |
A
B
Refer to Symptom Simulation.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Proceed to Diagnostic Trouble Code Chart.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT