Home › Drivetrain › K313 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.10–2020.08
RM32H0E _52 Drivetrain _059624 K313 MULTIDRIVE / CVT _0292538 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K313 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P282813  Pressure Control Solenoid "K" Circuit Open  


DESCRIPTION

According to current from the ECM, the shift solenoid valve SLS controls secondary pulley pressure and belt clamping pressure in accordance with the input shaft torque.

C267073C01
5.094,0.646 4.875,0.188 4.875,0.188 4.729,0.188 true 4.75,0.885 4.625,1.083 4.625,1.083 4.198,1.083 true 5.885,0.396 5.26,1.313 5.26,1.313 5.896,0.969 true 1.969,1.385 2.26,1.615 0.292,0.229 10 false *b 1.177,0.542 1.385,0.792 0.208,0.25 10 false *a 4.583,0.104 4.781,0.313 0.198,0.208 10 false *1 4.01,1 4.229,1.188 0.219,0.188 10 false *2 5.073,1.24 5.292,1.479 0.219,0.24 10 false *3
*1 Spool Valve *2 Sleeve
*3 Solenoid Coil - -
*a Hydraulic Pressure *b Current Flow to Solenoid


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P282813 Pressure Control Solenoid "K" Circuit Open While the vehicle is driven, an open or a short is detected in the shift solenoid valve SLS circuit for 1 second or more (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (Shift solenoid valve SLS)

·

ECM


Comes on DTC stored SAE Code:
P282B

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SLS circuit. If there is an open or short in the shift solenoid valve SLS circuit, the ECM detects the malfunction, illuminates the MIL and stores this DTC.

WIRING DIAGRAM

C319938E28
0.844,1.979 4.51,2.177 3.667,0.198 10 false Shift Solenoid Valve SLS 1.063,2.771 3.708,3.24 2.646,0.469 10 false Continuously Variable Transaxle Assembly (Transmission Wire) 1.073,2.604 1.531,2.802 0.458,0.198 10 false C40 5.802,2.813 6.26,3.01 0.458,0.198 10 false C62 5.802,2.969 6.26,3.167 0.458,0.198 10 false ECM 3.896,0.771 4.51,0.969 0.615,0.198 10 false SLS+ 5.281,0.771 5.896,0.969 0.615,0.198 10 false SLS+ 5.281,1.552 5.896,1.75 0.615,0.198 10 false SLS- 3.917,1.542 4.531,1.74 0.615,0.198 10 false SLS- 5.823,0.521 6.438,0.719 0.615,0.198 10 false 12 V 5.083,0.76 5.396,0.958 0.313,0.198 10 false 1 5.021,1.542 5.333,1.74 0.313,0.198 10 false 31 4.333,1.542 4.646,1.74 0.313,0.198 10 false 12 4.365,0.771 4.677,0.969 0.313,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLS)
a.
C264597C11
0.844,0.469 1.021,0.469 1.021,0.469 1.281,0.885 true 0.844,1.583 1.042,1.583 1.042,1.583 1.271,1.198 true 0.198,0.219 0.51,0.417 0.313,0.198 10 *a 0.458,1.531 0.896,1.74 0.438,0.208 10 SLS- 0.479,0.406 1.094,0.604 0.615,0.198 10 SLS+
*a Component without harness connected
(Transmission Wire)


Disconnect the C40 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (SLS+) - 12 (SLS-) 20°C (68°F) 5.0 to 5.6 Ω
5 (SLS+) - Body ground and other terminals Always 10 kΩ or higher
12 (SLS-) - Body ground and other terminals Always 10 kΩ or higher



c.

Connect the C40 transmission wire connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C326700C25
1.427,0.198 1.813,0.427 0.385,0.229 0.563,0.292 0.333,0.885 true 0.333,1.667 0.333,0.958 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 0.177,1.677 0.938,1.896 0.76,0.219 10 false 31 (SLS-) 0.49,0.115 1.25,0.333 0.76,0.219 10 false 1 (SLS+) 1.51,0.24 1.969,0.438 0.458,0.198 10 false C62
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C62-1 (SLS+) - C62-31 (SLS-) 20°C (68°F) 5.0 to 5.6 Ω
C62-1 (SLS+) - Body ground and other terminals Always 10 kΩ or higher
C62-31 (SLS-) - Body ground and other terminals Always 10 kΩ or higher



c.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT