After moving the shift lever to M, it is possible to change the shift range between M1 and M7 using the shift lever. Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" lowers the shift range by one.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
| Tester Display |
|---|
| Shift SW Status (S Range) |
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift SW Status (S Range) | Transmission control switch status | ON or OFF | ·
ON: Shift lever in M, "+" or "-" ·
OFF: Shift lever not in M, "+" or "-" |
- |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
| Tester Display |
|---|
| Sport Shift Up SW |
| Sport Shift Down SW |
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sport Shift Up SW | Sport shift up switch status | OFF or ON | ·
ON: Shift lever held in "+" ·
OFF: Shift lever not held in "+" |
- |
| Sport Shift Down SW | Sport shift down switch status | OFF or ON | ·
ON: Shift lever held in "-" ·
OFF: Shift lever not held in "-" |
- |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal | B |
A
B
| *A | for LHD |
| *B | for RHD |
| *a | Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch)) |
Disconnect the F17 shift lock control unit assembly (transmission control switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (SFTU) - 2 (E) | Shift lever held in "+" | Below 1 Ω |
| 3 (SFTU) - 2 (E) | Shift lever in M | 10 kΩ or higher |
| 1 (SFTD) - 2 (E) | Shift lever held in "-" | Below 1 Ω |
| 1 (SFTD) - 2 (E) | Shift lever in M | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (SFTU) - 2 (E) | Shift lever held in "+" | Below 1 Ω |
| 1 (SFTU) - 2 (E) | Shift lever in M | 10 kΩ or higher |
| 3 (SFTD) - 2 (E) | Shift lever held in "-" | Below 1 Ω |
| 3 (SFTD) - 2 (E) | Shift lever in M | 10 kΩ or higher |
Connect the F17 shift lock control unit assembly (transmission control switch) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A38 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-43 (SFTD) - Body ground | Shift lever held in "-" | Below 1 Ω |
| A38-43 (SFTD) - Body ground | Shift lever in M | 10 kΩ or higher |
| A38-42 (SFTU) - Body ground | Shift lever held in "+" | Below 1 Ω |
| A38-42 (SFTU) - Body ground | Shift lever in M | 10 kΩ or higher |
Connect the A38 ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch)) |
Disconnect the F17 shift lock control unit assembly (transmission control switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (IG) - 5 (S) | Shift lever in M | Below 1 Ω |
| 4 (IG) - 5 (S) | Shift lever not in M | 10 kΩ or higher |
Connect the F17 shift lock control unit assembly (transmission control switch) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Shift Lock Control Unit Assembly (Transmission Control Switch)) |
Disconnect the shift lock control unit assembly (transmission control switch) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F17-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| F17-4 (IG) - Body ground | Ignition switch off | Below 1 V |
Connect the shift lock control unit assembly (transmission control switch) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F17 shift lock control unit assembly (transmission control switch) connector.
Disconnect the A38 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F17-5 (S) - A38-59 (S) | Always | Below 1 Ω |
| F17-5 (S) - Body ground and other terminals | Always | 10 kΩ or higher |
| A38-59 (S) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the A38 ECM connector.
Connect the F17 shift lock control unit assembly (transmission control switch) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT