The outer mirror switch assembly sends a mirror auto retract/return signal to the main body ECU (multiplex network body ECU) when the retractable outer mirror switch on the outer mirror switch assembly is in the AUTO position. The main body ECU (multiplex network body ECU) retracts or returns the outer rear view mirror assemblies based on the lock/unlock signal of each door while the ignition switch is off.
for LHD
for RHD
Inspect the fuses for circuits related to this system before performing the following procedure.
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*1
*1: w/ Entry and Start System
Check the power retract mirror function.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM>OPERATION CHECK
Power retract mirror function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the power door lock control system.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Power door lock control system is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
w/ Entry and Start System
Check the wireless door lock control system.
w/o Entry and Start System
Check the wireless door lock control system.
Wireless door lock control system is normal.
| Result | Proceed to |
|---|---|
| OK (w/ Entry and Start System) | A |
| OK (w/o Entry and Start System) | B |
| NG (w/ Entry and Start System) | C |
| NG (w/o Entry and Start System) | D |
A
B
C
D
Check the entry and start system (for Entry Function).
Entry and start system (for Entry Function) is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Auto Mirror SW | Retractable outer mirror switch signal | OFF or ON | OFF: Mirror retract switch not in auto position
ON: Mirror retract switch in auto position |
- |
| Tester Display |
|---|
| Auto Mirror SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Remove the outer mirror switch assembly.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL
Inspect the outer mirror switch assembly.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I12*1 or J10*2 outer mirror switch assembly.
*1: for RHD
*2: for LHD
Disconnect the F16 main body ECU (multiplex network body ECU).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I12-2 (MAT) - F16-15 (RTR) | Always | Below 1 Ω |
| I12-2 (MAT) or F16-15 (RTR) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J10-4 (MAT) - F16-15 (RTR) | Always | Below 1 Ω |
| J10-4 (MAT) or F16-15 (RTR) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C