Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for LHD) › 2016.10–2019.09
RM32H0E _57 Power Source / Network _060596 POWER DISTRIBUTION _0297231 MAIN BODY ECU(for LHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the main body ECU (multiplex network body ECU) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)*2 Stop and start system (Click here)
Main body ECU (multiplex network body ECU) Perform code registration (Immobilizer system) Wireless door lock control system See Service Bulletin for the registration method. (w/ Entry and Start System)
Entry and start system
Engine start function
Steering lock system

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

*2: w/ Stop and start system

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 73900 3.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 67914 4.REMOVE FRONT DOOR SCUFF PLATE LH (w/o Driver Side Knee Airbag)

Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH (w/o Driver Side Knee Airbag)

Hide 55606 6.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 55470 7.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 55434B 8.REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL (w/o Driver Side Knee Airbag)

Hide 55404D 9.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 53601 10.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 55545 11.REMOVE FUSE BOX OPENING COVER (w/o Driver Side Knee Airbag)

Hide 55308B 12.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

Hide 82730 13.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

a.
E353743

Disengage the clamp.


b.
E353744

Disconnect 4 connectors.


c.
E353745C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws and pull down the lock levers to disconnect the 2 connectors as shown in the illustration.


d.
E353746

Remove the bolt and nut.


e.

Disengage the clamp.


f.

Pull out the instrument panel junction block assembly with main body ECU.


g.
E353747

Disengage the clamp.


h.
E353748C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clamp.


i.

Disengage the claws and pull down the lock levers to disconnect the 2 connectors as shown in the illustration.


j.

Remove the instrument panel junction block assembly with main body ECU.


Hide 89221 14.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

a.
E353749

Remove the bolt.


b.

Disengage the clamp to remove the wiring harness clamp bracket.


c.
E336530C01
0.188,2.813 0.51,2.813 true 0.719,2.854 1.135,2.854 true 1.167,2.76 1.479,2.917 0.313,0.156 10 false *1 0.031,2.719 0.344,2.875 0.313,0.156 10 false *2
*1 Instrument Panel Junction Block Assembly
*2 Main Body ECU (Multiplex Network Body ECU)
V100135

Push in this Direction


Press the claw of the instrument panel junction block assembly as shown in the illustration to release the lock.


d.
E336535C01
1.5,1.917 1.688,1.688 false 1.396,1.917 1.708,2.073 0.313,0.156 10 false *a
*a Protective Tape
V100135

Insert in this Direction
V113147

Remove in this Direction


With the instrument panel junction block assembly lock released, insert a screwdriver with its tip wrapped in protective tape horizontally between the main body ECU (multiplex network body ECU) and the instrument panel junction block assembly.

NOTICE:
·

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).

·

Do not insert the screwdriver under the connector socket of the main body ECU (multiplex network body ECU).




e.

Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.

NOTICE:

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).



f.
E336537C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Raise the main body ECU (multiplex network body ECU) as shown by the arrow (1), and then pull it out as shown by the arrow (2) in the illustration.

NOTICE:

Do not touch the main body ECU (multiplex network body ECU) connector.