Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for RHD) › 2016.10–2019.09
RM32H0E _57 Power Source / Network _060596 POWER DISTRIBUTION _0299480 MAIN BODY ECU(for RHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the main body ECU (multiplex network body ECU) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)*2 Stop and start system (Click here)
Main body ECU (multiplex network body ECU) Perform code registration (Immobilizer system) Wireless door lock control system See Service Bulletin for the registration method. (w/ Entry and Start System)
Entry and start system
Engine start function
Steering lock system

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

*2: w/ Stop and start system

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55433B 3.REMOVE NO. 2 INSTRUMENT PANEL LOWER FINISH PANEL

Hide 82878 4.REMOVE ECU INTEGRATION BOX LH

Hide 82730 5.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

a.
E353750

Disconnect the 2 connectors.


b.
E353751

Disengage the clamp.


c.

Remove the bolt and nut.


d.

Pull out the instrument panel junction block assembly with main body ECU.


e.
E353752

Disengage the clamp.


f.
E353753C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clamp.


g.

Disengage the claws and pull down the lock levers to disconnect the 2 connectors as shown in the illustration.


h.

Remove the instrument panel junction block assembly with main body ECU.


Hide 89221 6.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

a.
E336530C01
0.188,2.813 0.51,2.813 true 0.719,2.854 1.135,2.854 true 1.167,2.76 1.479,2.917 0.313,0.156 10 false *1 0.031,2.719 0.344,2.875 0.313,0.156 10 false *2
*1 Instrument Panel Junction Block Assembly
*2 Main Body ECU (Multiplex Network Body ECU)
V100135

Push in this Direction


Press the claw of the instrument panel junction block assembly as shown in the illustration to release the lock.


b.
E336535C01
1.5,1.917 1.688,1.688 false 1.396,1.917 1.708,2.073 0.313,0.156 10 false *a
*a Protective Tape
V100135

Insert in this Direction
V113147

Remove in this Direction


With the instrument panel junction block assembly lock released, insert a screwdriver with its tip wrapped in protective tape horizontally between the main body ECU (multiplex network body ECU) and the instrument panel junction block assembly.

NOTICE:
·

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).

·

Do not insert the screwdriver under the connector socket of the main body ECU (multiplex network body ECU).




c.

Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.

NOTICE:

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).



d.
E336537C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Raise the main body ECU (multiplex network body ECU) as shown by the arrow (1), and then pull it out as shown by the arrow (2) in the illustration.

NOTICE:

Do not touch the main body ECU (multiplex network body ECU) connector.