Home › Engine / Hybrid System › 3ZR-FAE (INTAKE / EXHAUST) › EXHAUST MANIFOLD
RM32H0E _51 Engine / Hybrid System _059727 3ZR-FAE INTAKE / EXHAUST _0292823 EXHAUST MANIFOLD A

3ZR-FAE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold with the 4 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17141 2.INSTALL EXHAUST MANIFOLD

a.

Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.


b.
A393212

Temporarily install the exhaust manifold with 5 new nuts.


c.
A393211C01
2.604,1.271 2.76,1.469 0.156,0.198 10 true 1 2.76,0.604 2.917,0.802 0.156,0.198 10 true 2 0.5,0.958 0.656,1.156 0.156,0.198 10 true 3

Temporarily install the manifold stay with the 3 bolts.


d.

Tighten the 5 exhaust manifold nuts.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17167 3.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 4 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

Install the wire harness clamp bracket to the cylinder head sub-assembly with the bolt.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


c.

Engage the 3 clamps.


Hide 17410 5.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst)

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length (Front) 41.5 mm (1.63 in.)
Minimum Free Length (Rear) 38.5 mm (1.52 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install 2 new exhaust pipe gaskets to the exhaust manifold and front exhaust pipe assembly (TWC: Front and Rear Catalyst).


c.
A181728C59
2.927,1.438 2.802,1.438 2.802,1.438 2.5,1.75 false 1.656,3.219 2.031,3.219 2.031,3.219 2.031,2.438 false 1.458,0.656 1.813,0.656 1.813,0.656 1.813,1.115 false 1.313,0.563 1.604,0.781 0.292,0.219 10 false *1 3.031,1.333 3.313,1.542 0.281,0.208 10 false *a 1.438,3.146 1.76,3.385 0.323,0.24 10 false *2
*1 Exhaust Manifold or Front Exhaust Pipe Assembly (TWC: Front and Rear Catalyst)
*2 Exhaust Pipe Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in each exhaust pipe gasket until its surface is flush with the exhaust manifold and front exhaust pipe assembly (TWC: Front and Rear Catalyst).

NOTICE:
·

Be sure to install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gaskets.

·

Do not damage the exhaust pipe gaskets.

·

Do not push in the exhaust pipe gaskets by using the exhaust pipes when connecting them.




d.

Connect the front exhaust pipe assembly (TWC: Front and Rear Catalyst) to the 2 exhaust pipe supports.


e.

Install the front exhaust pipe assembly (TWC: Front and Rear Catalyst) to the exhaust manifold with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C18
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Exhaust Manifold
*2 Front Exhaust Pipe Assembly (TWC: Front and Rear Catalyst)
*3 Exhaust Pipe Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold and front exhaust pipe assembly (TWC: Front and Rear Catalyst) is consistent front-to-rear and left-to-right.



f.

Install the front exhaust pipe assembly (TWC: Front and Rear Catalyst) to the tail exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C37
2.396,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.104,0.604 false 0.781,1.188 0.938,1.188 0.938,1.188 1.094,0.885 false 0.406,1.417 0.573,1.573 0.167,0.156 10 *a 0.604,0.177 0.802,0.375 0.198,0.198 10 *1 0.604,1.135 0.813,1.333 0.208,0.198 10 *2 2.719,0.115 2.885,0.271 0.167,0.156 10 *3
*1 Front Exhaust Pipe Assembly (TWC: Front and Rear Catalyst)
*2 Tail Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the front exhaust pipe assembly (TWC: Front and Rear Catalyst) and tail exhaust pipe assembly is consistent front-to-rear and left-to-right.



g.

Engage the wire harness clamp.


h.

Connect the heated oxygen sensor connector.


Hide 57533B 6.INSTALL FRONT FLOOR CENTER BRACE

a.

Install the 3 front floor center braces to the vehicle body with the 12 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51441 8.INSTALL NO. 1 ENGINE UNDER COVER