Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. PRECAUTION
Make sure to perform initialization after replacing the air conditioning radiator damper servo sub-assembly. If initialization is not performed, the air conditioner unit assembly will not perform properly as the air conditioning amplifier assembly will not be able to recognize the position of the air conditioning radiator damper sub-assembly.
87211A
2.REMOVE NO. 2 AIR DUCT (for LHD)
|
Remove in this Direction |
Remove the screw.
Disengage the claws to remove the No. 2 air duct as shown in the illustration.
87211
3.REMOVE NO. 1 AIR DUCT (for RHD)
|
Remove in this Direction |
Remove the screw.
Disengage the claws to remove the No. 1 air duct as shown in the illustration.
88505
4.REMOVE AIR CONDITIONING DUCT SUB-ASSEMBLY
Disengage the guide to remove the air conditioning duct sub-assembly.
88482A
5.REMOVE COVER (w/o Rear Air Duct)
Disengage the claws to remove the cover.
82143
6.REMOVE NO. 3 INSTRUMENT PANEL WIRE (w/ PTC Heater)
Disconnect the connector.
Disengage the clamps to remove the No. 3 instrument panel wire.
88539E
7.REMOVE NO. 3 COOLER UNIT DRAIN HOSE
Remove the No. 3 cooler unit drain hose.
87130D
8.REMOVE BLOWER ASSEMBLY
87114B
9.REMOVE HEATER COVER (w/o PTC Heater)
|
Remove in this Direction |
Remove the 2 screws and heater cover as shown in the illustration.
87114L
10.REMOVE NO. 2 HEATER COVER (w/ PTC Heater)
Remove the screw and No. 2 heater cover.
87710G
11.REMOVE QUICK HEATER ASSEMBLY (w/ PTC Heater)
|
Remove in this Direction |
Remove the 2 screws and quick heater assembly as shown in the illustration.
88650N
12.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY
for LHD:
Disconnect the connector.
Remove the screw.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the guides to remove the air conditioning amplifier assembly as shown in the illustration.
for RHD:
Disconnect the connector.
Remove the screw.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the guides to remove the air conditioning amplifier assembly as shown in the illustration.
82210K
13.REMOVE AIR CONDITIONING HARNESS ASSEMBLY
for Automatic Air Conditioning System:
Disconnect the 5 connectors.
Disengage clamps to remove the air conditioning harness assembly.
for Manual Air Conditioning System:
Disconnect 3 connectors.
Disengage clamps to remove the air conditioning harness assembly.
88539J
14.REMOVE DRAIN COOLER HOSE
Remove the drain cooler hose.
88539C
15.REMOVE NO. 2 COOLER UNIT DRAIN HOSE
Remove the No. 2 cooler unit drain hose.
87050C
16.REMOVE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)
for Upper LH Side:
|
Remove in this Direction |
Turn the No. 1 air conditioning radiator damper servo sub-assembly to disengage the claw as shown in the illustration.
|
Remove in this Direction |
Remove the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.
for Lower LH Side:
|
Remove in this Direction |
Disengage the snap.
Turn the No. 1 air conditioning radiator damper servo sub-assembly to disengage the claw as shown in the illustration.
|
Remove in this Direction |
Remove the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.
for Upper RH Side:
|
Remove in this Direction |
Turn the No. 1 air conditioning radiator damper servo sub-assembly to disengage the claw.
|
Remove in this Direction |
Remove the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.
for Lower RH Side:
|
Remove in this Direction |
Disengage the snap.
Turn the No. 1 air conditioning radiator damper servo sub-assembly to disengage the claw as shown in the illustration.
|
Remove in this Direction |
Remove the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.
87050C
17.REMOVE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Manual Air Conditioning System)
for Upper RH Side:
|
Remove in this Direction |
Turn the No. 1 air conditioning radiator damper servo sub-assembly to disengage the claw as shown in the illustration.
|
Remove in this Direction |
Remove the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.
for Lower RH Side:
|
Remove in this Direction |
Disengage the snap.
Turn the No. 1 air conditioning radiator damper servo sub-assembly to disengage the claw as shown in the illustration.
|
Remove in this Direction |
Remove the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.
87050D
18.REMOVE NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
|
Remove in this Direction |
Turn the No. 2 air conditioning radiator damper servo sub-assembly to disengage the claw as shown in the illustration.
|
Remove in this Direction |
Remove the No. 2 air conditioning radiator damper servo sub-assembly as shown in the illustration.
88897M
19.REMOVE HEATER PIPE GROMMET
Remove the heater pipe grommet.
87124B
20.REMOVE HEATER CLAMP
Remove the screw.
Disengage the claws to remove the heater clamp.
87107A
21.REMOVE HEATER RADIATOR UNIT SUB-ASSEMBLY
Remove the 3 screws.
|
Remove in this Direction |
Remove the heater radiator unit sub-assembly as shown in the illustration.
Prepare a drain pan or cloth in case the coolant leaks.
88515
22.REMOVE COOLER EXPANSION VALVE
Using a 4 mm hexagon socket wrench, remove the 2 hexagon bolts and cooler expansion valve.
Remove the 2 O-rings from the No. 1 cooler evaporator sub-assembly.
Remove the grommet.
87611A
23.REMOVE HEAT EXCHANGER CASE
Remove the 2 screws and the bracket.
Disengage the claws and guide, and remove the screw to remove the heat exchanger case.
87102A
24.REMOVE RADIATOR CASE SUB-ASSEMBLY
Remove the 3 screws.
Disengage the claws to remove the radiator case sub-assembly.
88501
25.REMOVE NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
|
Remove in this Direction |
Disconnect the the connector.
Remove the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor as shown in the illustration.
87102B
26.REMOVE NO. 2 RADIATOR CASE SUB-ASSEMBLY
Remove the 6 screws and the No. 2 radiator case sub-assembly.
88625
27.REMOVE NO. 1 COOLER THERMISTOR